---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Mon 09/21/20: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:55 AM - Re: Undercarriage & Flap Lever on the XS Mono Wheel () 2. 06:45 AM - Re: Undercarriage & Flap Lever on the XS Mono Wheel () 3. 02:08 PM - Re: How to properly hoist a Europa Trigear (=?UTF-8?Q?Erik_Dahlb=c3=a4ck?=) 4. 03:19 PM - Re: How to properly hoist a Europa Trigear (david park) ________________________________ Message 1 _____________________________________ Time: 04:55:45 AM PST US From: Subject: RE: Europa-List: Undercarriage & Flap Lever on the XS Mono Wheel My thoughts on this: Any extra long lever would need to be dog legged as the top of the existing lever fits into the recess in the panel. Also the force needed is very depended on getting the bungee tension correct. If this is high enough then the force needed to retract or engage the undercarriage will be minimal. Roddy Kesteton G-IKRK -----Original Message----- From: owner-europa-list-server@matronics.com On Behalf Of Mallard Sent: 18 September 2020 16:07 Subject: Europa-List: Undercarriage & Flap Lever on the XS Mono Wheel Has anyone ever created an extra long lever or an additional attachment to make the Undercarriage Lever easier to operate? I have arthritis in the knuckle joints of the first 2 fingers of my right hand and found it quite difficult to push the lever forward to put down the Mono Wheel & Flaps. I was thinking of a longer lever which would give more leverage? Thanks in advance for any suggestions/advice. James -------- Seat of my pants Read this topic online here: http://forums.matronics.com/viewtopic.php?p=498413#498413 ________________________________ Message 2 _____________________________________ Time: 06:45:45 AM PST US From: Subject: RE: Europa-List: Undercarriage & Flap Lever on the XS Mono Wheel James, Ted Gladstone and Justin Kennedy have done several mods to their Monowheel Z-TED, including the following reported on the Matronics list as follows: From: Edward Gladstone Subject: tric Flaps on Monowheel >Shaun Simpkins wrote:- > >Has anyone out there tried decoupling the flaps and gear on a monowheel< We are the Edinburgh group who have fitted an electric screwjack actuator to operate the flaps on our monowheel Europa. Rowland is correct in that the actuator was originally designed to operate the elevation mechanism on a lounge chair or bed for the elderly. It weighs about the same as the long cranked linking tube and its associated couplings. We also developed a manual emergency method lowering the flaps, should the electric motor fail, but Francis Donaldson (PFA Chief Engineer) did no share our enthusiasm for it and we locked out this device. Along with many other mods we have also changed the lever that operates the undercarriage such that it rotates from a horizontal position on the tunnel through 180 deg to end up again in the horizontal position on the tunnel. It allows us to fill up the cavity in the instrument panel and it can now be operated with a single finger! The electric flap motor also operates the outriggers in the normal manner (for the time being) but we have the intention to also operate the outriggers with small electric screw jack actuators. When this is done we will be able to operate the flaps to any angle but, with the existing setup, we can go down to 30 deg and op to 23 deg without unlatching the outriggers. At the moment we have decided to abandon any further mods and concentrate on getting it flying ( it's kit No 15!!!). When its flying we can amuse ourselves with our further mods and go faster fairings. Ted & Justin G-ZTED While this may be too radical a solution for you, the principle involved in making the undercarriage lever rotate through 180=B0 has clearly resulted in a very light operating force. I have always found Ted and Justin very willing to share their Europa experiences and am sure they would be happy to discuss ideas on the subject. Best regards, Mike Dr Mike Gregory Kit 94 01480 451655 07885 355765 -----Original Message----- From: owner-europa-list-server@matronics.com On Behalf Of Mallard Sent: 18 September 2020 16:07 Subject: Europa-List: Undercarriage & Flap Lever on the XS Mono Wheel james@kingdom.ie> Has anyone ever created an extra long lever or an additional attachment to make the Undercarriage Lever easier to operate? I have arthritis in the knuckle joints of the first 2 fingers of my right hand and found it quite difficult to push the lever forward to put down the Mono Wheel & Flaps. I was thinking of a longer lever which would give more leverage? Thanks in advance for any suggestions/advice. James -------- Seat of my pants Read this topic online here: http://forums.matronics.com/viewtopic.php?p=498413#498413 ________________________________ Message 3 _____________________________________ Time: 02:08:11 PM PST US Subject: Re: Europa-List: How to properly hoist a Europa Trigear From: =?UTF-8?Q?Erik_Dahlb=c3=a4ck?= Thanks, Am I correct in assuming that the aforementioned metal rod (would a sturdy tube do?) goes in where the attachment for the wheel pants goes in? Or does that one somehow fit into something else that is mounted within the wheel axis? (please see attached photo) Any other options BTW? What if you needed to work on the landing gear strut for an example, and didn't want the fuselage to be standing on it? I saw that suggestion about suspending the fuselage from the engine mounts and the tail. My local mechanic who's helping me with all this wasn't very fond at all of that idea. / Erik On 2020-09-18 12:46, Karl Heindl wrote: > HI Erik, > Use an aluminium or steel rod, can't remember the diameter, and push > into the leg, first remove the cotter pin. Length should be at least > 50cm. then jack it up with your hydraulic jack. You can now remove the > wheel up to the jack. > Now place a block of wood under the leg end and lower the jack and > remove it, and the wheel. > For the nose gear I had an eye bolt mounted in the garage floor. Then > used a ratcheting strap just > ahead of the fin, looped through the eye bolt, and lowered the tail > that way. Or get someone to push down the tail. > Karl > > ------------------------------------------------------------------------ > *From:* owner-europa-list-server@matronics.com > on behalf of Erik Dahlbck > > *Sent:* 18 September 2020 09:14 > *To:* europa-list@matronics.com > *Subject:* Europa-List: How to properly hoist a Europa Trigear > > > Hello again, > > One hopefully simple question: How do you best hoist (or jack) a Europa > Trigear for landing gear maintenance? > > At some point on the fuselage? On big cushioned plates under the wings, > centered under the main spar? > > Also, is it safe to lift the nose wheel by pushing down the rear part of > the fuselage, perhaps using a wide collar placed just ahead of the > thinnest point, strapped to a weight or attaching point on the floor? > > > Sincerely, > > Erik Gunneland Dahlbck > > ========== > st Email Forum - > pa-List">http://www.matronics.com/Navigator?Europa-List > ========== > p; - MATRONICS WEB FORUMS - > ums.matronics.com > ========== > p; - NEW MATRONICS LIST WIKI - > matronics.com > ========== > p; - List Contribution Web Site - > p; -Matt Dralle, List Admin. > http://www.matronics.com/contribution > ========== > > ________________________________ Message 4 _____________________________________ Time: 03:19:30 PM PST US From: david park Subject: Re: Europa-List: How to properly hoist a Europa Trigear To raise the nose wheel I use at least two 30 liter cans of fuel/water to we igh down the tail with a padded strop over the fuselage in front of the fin. To service main wheels I use the method described using a piece of steel tub e pushed in to the axle, a jack and a piece of 1 inch ply to support the leg .. Dave Park G-LDVO > On 21 Sep 2020, at 22:17, Erik Dahlb=C3=A4ck wrote : > > =EF=BB > Thanks, > > Am I correct in assuming that the aforementioned metal rod (would a sturdy tube do?) goes in where the attachment for the wheel pants goes in? Or does that one somehow fit into something else that is mounted within the wheel a xis? (please see attached photo) > > Any other options BTW? What if you needed to work on the landing gear stru t for an example, and didn't want the fuselage to be standing on it? > > I saw that suggestion about suspending the fuselage from the engine mounts and the tail. My local mechanic who's helping me with all this wasn't very f ond at all of that idea. > > / Erik > >> On 2020-09-18 12:46, Karl Heindl wrote: >> HI Erik, >> Use an aluminium or steel rod, can't remember the diameter, and push into the leg, first remove the cotter pin. Length should be at least 50cm. then j ack it up with your hydraulic jack. You can now remove the wheel up to the j ack. >> Now place a block of wood under the leg end and lower the jack and remove it, and the wheel. >> For the nose gear I had an eye bolt mounted in the garage floor. Then us ed a ratcheting strap just >> ahead of the fin, looped through the eye bolt, and lowered the tail that w ay. Or get someone to push down the tail. >> Karl >> >> From: owner-europa-list-server@matronics.com on behalf of Erik Dahlb=C3=A4ck >> Sent: 18 September 2020 09:14 >> To: europa-list@matronics.com >> Subject: Europa-List: How to properly hoist a Europa Trigear >> >> >> Hello again, >> >> One hopefully simple question: How do you best hoist (or jack) a Europa >> Trigear for landing gear maintenance? >> >> At some point on the fuselage? On big cushioned plates under the wings, >> centered under the main spar? >> >> Also, is it safe to lift the nose wheel by pushing down the rear part of >> the fuselage, perhaps using a wide collar placed just ahead of the >> thinnest point, strapped to a weight or attaching point on the floor? >> >> >> Sincerely, >> >> Erik Gunneland Dahlb=C3=A4ck >> >> ========== >> st Email Forum - >> pa-List">http://www.matronics.com/Navigator?Europa-List >> ========== >> p; - MATRONICS WEB FORUMS - >> ums.matronics.com >> ========== >> p; - NEW MATRONICS LIST WIKI - >> matronics.com >> ========== >> p; - List Contribution Web Site - >> p; -Matt Dralle, List Admin. >> http://www.matronics.com/contribution >> ========== >> >> >> > >
------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message europa-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Europa-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/europa-list Browse Digests http://www.matronics.com/digest/europa-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.