Europa-List Digest Archive

Mon 05/30/22


Total Messages Posted: 3



Today's Message Index:
----------------------
 
     1. 08:29 AM - What Did you do with your Europa this week 5/23-5/30 (crouton)
     2. 04:00 PM - Re: Matronics Email & Email List Server Back Online... (Matt Dralle)
     3. 07:21 PM - What did you do with your Europa this week 5/30 - 6/6 (h&jeuropa)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:29:56 AM PST US
    From: crouton <crouton@well.com>
    Subject: What Did you do with your Europa this week 5/23-5/30
    After a couple of weeks of adjustment and maintenance I departed KEYW. Take off 07:50, 1.3hr to KPGD where I picked up some tools and cool weather gear and filled up with 91 octane and launched at 10:00 for KSFQ (Suffolk, VA), arriving 15:30. I cruised at 9.5, pretty much direct, with flight following routing around the nearly impenetrable maze of military airspace. By the way, I really advocate Sunday as a travel day from south Florida because it is a day of rest even for the military. I had only two short deviations from my direct routing. I flew at 9.5 because I had a serious tailwind of 20kt. Its a good use of the Hac-man mixture control and I was able to true 122kt at 3.5gph and 4800rpm. Over the years I have discovered that the leaning is not entirely effective at altitude with WOT. It certainly leans, but to really get it lean, you have to gradually retard the throttle until you notice a slight decrease in MAP, increase the throttle just enough to restore MAP, about 22in at this altitude and monitor EGT. By juggling the throttle and mixture controls the fuel flows can be very accurately controlled. I find that after several minutes of stable cruise I move the throttle open a tiny amount while monitoring the EGTs (opening the throttle very slightly at altitude in stable cruise will richen the mixture slightly). I have to emphasize that this mixture trimming is accomplished by REALLY TINY throttle movements and close attention to MAP and EGT. Also remember there is a perceptible time lag for the carb vacuums to stabilize. After all you are going to be up there for some hours and what else do you have to do? Suffolk has 91 octane auto and a barbecue restaurant which unfortunately closed at 16:00, but I got a coffee. Same deal as the previous leg. Flight following got me through Washington and NYC at 7500 this time, similar fuel flows and TAS 125-128kt. I can go a few knots faster by turning 5000 or 5200 but it burns 4+ and I dont think its worth it. Torque peak is close to 4800 and piston engines are most efficient and happy there. Flying over NYC on a CAVU day was impressive. That sucker is big and dense. It doesnt make me want to live there. The storms I had been racing blocked my route up the Connecticut River to KEEN, my base, so I flew ENE hoping to accomplish an end run to KEEN from the north. No such luck. Couldnt get to KPWM either so I deviated to KPSM and got tied down just a couple of minutes before the gust front and the rain. ET 3:45. Not a bad day of flying. > I spent the evening and the next day with a good friend of many decades and flew to KEEN, taking off at 16:00 for a 45 minute flight. The Europa is a good cross country airplane with the long ranger aux tank. With my straight 912 it cruises at C 182 speeds on about a third of the fuel, the cockpit is comfortable and relatively roomy and if you have an XS you have more room and with a 912S, better climb and cruise at altitude. I have a classic mono with a straight 912, so I can only wish and envy. Creighton Smith A-009 > >


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:00:45 PM PST US
    Subject: Re: Matronics Email & Email List Server Back Online...
    From: "Matt Dralle" <dralle@matronics.com>
    Mac.com uses Proofpoint to block for incoming spam. They have erroneously blocked all of the Matronics IP addresses associated with email (96.68.171.1/96.68.171.4). Please contact them the tell them, they are blocking legitimate emails. https://support.proofpoint.com/dnsbl-lookup.cgi?ip'.68.171.1 I have tried, but they just think I'm a spammer an ignore me. A few customers need to complain. Thanks, Matt Dralle -------- Matt Dralle Matronics Email List Administrator Read this topic online here: http://forums.matronics.com/viewtopic.php?p=507087#507087


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 07:21:01 PM PST US
    Subject: What did you do with your Europa this week 5/30 - 6/6
    From: "h&amp;jeuropa" <butcher43@att.net>
    Starting thread for this week. We completed our condition inspection and test flights! Jim Read this topic online here: http://forums.matronics.com/viewtopic.php?p=507089#507089




    Other Matronics Email List Services

  • Post A New Message
  •   europa-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Europa-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/europa-list
  • Browse Europa-List Digests
  •   http://www.matronics.com/digest/europa-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --