---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Mon 12/05/22: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:22 AM - Re: The Obsidian File - Mono Undercarriage (D McFadyean) 2. 05:18 AM - Re: The Obsidian File - Mono Undercarriage (Area-51) 3. 04:45 PM - Anti Door Warping (rparigoris) 4. 05:27 PM - Re: Anti Door Warping (Pete) ________________________________ Message 1 _____________________________________ Time: 02:22:33 AM PST US From: D McFadyean Subject: Re: Europa-List: The Obsidian File - Mono Undercarriage A further demonstration that the monowheel doesn't comply with CS-VLA (in respect of side loads on the main under carriage). Duncan McF. > On 03 December 2022 at 16:44 Pete wrote: > > > > > > Fwiw, my experience: > > 1- difficulty in getting the gear into to and out of the up-gate (regardless of bungy tension) was due to the flap rod adjustment being too short, causing the flaps to top-out, restricting the gear up travel. > > 2- general binding of the swing-arm was due to a bent gear/engine frame pivot tube. Bent due to having been side loaded when the gear was in the down position, an angle where that tube is totally unbraced/supported. I suspect many frames in the field are bent. The builder of my bird had actually shimmed the arm bushing to accommodate and reduce the binding (band aid solution). When repairing my frame, i added a truss to the frame at the correct angle to support the tube and prevent any future bending. > > 3- the bungee is simply to assist the pilot in raising the gear. I tensioned mine such that it pulls the gear up about 60% when doing the gear swing test. I find that with this tension my gear takes minimal effort over its entire swing range in flight. > > Cheers, > PeteZ > > > > > > > > > On Dec 3, 2022, at 9:55 AM, Area-51 wrote: > > > > > > With the 3D aero model now complete its onto a new chapter as mechanical and ancillaries come into the fore; and fruit has arrived straight off the get go. > > > > After reading and hearing about so many issues regarding the mono retract the first thing that has been focused upon is the undercarriage. Having the model available now provides the ability to try things out and get answers almost instantly. So that's exactly what happened as soon as the remaining components of the assembly were drafted and imported into the picture today. > > > > The first goto was undercarriage action; why does it jam closed on some aircraft? Why is it so difficult to retract when throwing that final bit of the lever forward? It was interesting what showed up! An initial earlier solution drafted last year was quickly thrown in the bin but it was this study that revealed where the issue actually now resided. > > > > Having the 3D CAD components assembled allowed a study of the geometry of the retractable assembly, and sure enough it was so very possible to jam the undercarriage in the retracted position; and was remarkably easy to affect; literally just a mm or two beyond the gate stop on the console did it and the wheel was stuck fast in the tunnel void. > > > > It was instantly apparent that the only way this could geometrically be possible is if one of the mechanical arms has moved passed a point to rest within a 90deg quadrant. So that's where the focus went to and thats what was quickly flushed out... the rubber block assembly had crossed over and was resting at 80deg to the swing of its upstream link. And there it was, with the only thing preventing jamming in situ now being the weight of the main wheel overcoming the tension of the bungee spring... Its the very same reason causing that last bit of retract throw on the cockpit lever being difficult; and perhaps the very same reason some owners simply tighten up the bungee spring to get things to park up. (The attached geometry image shows the factory positioning at the blue circles, the magenta line being the 90deg quadrant marker relative to pin LG04's position, the blue line represents the rubber block assembly). > > > > So gee what to do? ?? Well what if things get realigned to their respective 90deg quadrant? worth a go; what's required? Rotate a single pivot point 10deg and revision of LG02A... So that's what got drafted out and presto, problem instantly gone away to the graveyard of great ideas... Amazing!!! Took all of five minutes to solve on the 2D and another 10 to draft up a new 3D functional component and check for clashing and binding. > > > > With pin LG04's position at LG02A now rotated 10deg on the spring blocks arc it is now geometrically impossible to jam the undercarriage; even if the main wheel somehow finds its way up through the tunnel ceiling to the instrument panel facia; which it now can do if the lever is moved beyond its gated travel. > > > > So that's it, MOD-XX... Done! > > > > Fitting of LG02A-XX and reboring of LG02 for LG04's amended position, being 150mm horizontal and 7mm vertical from the datum centre bore of LG03. > > > > The other attached images show the difference between LG02A and LG02A-XX; the position of the bungee pin on LG02-XX has also been raised a few mm for better operational clearance. > > > > So can somebody please explain what the bungee spring actually does??? I cannot find or identify a practical mechanical reason for it at all other than to overcome the existing geometry error; unless this perceived error is intentional? > > > > Thanks for reading everything; well done! > > > > > > > > > > Read this topic online here: > > > > http://forums.matronics.com/viewtopic.php?p=509435#509435 > > > > > > > > > > Attachments: > > > > http://forums.matronics.com//files/0c2811c4_5687_479e_8d89_ed360c7f4c9c_437.jpeg > > http://forums.matronics.com//files/5c1a69af_790e_4a51_a3bd_8506e15c35f6_343.jpeg > > http://forums.matronics.com//files/e8371182_c043_4319_a5aa_c216cd42e8bb_157.jpeg > > http://forums.matronics.com//files/f6e8ca6f_6a3a_43da_8d31_fb5ae6e8e277_189.jpeg > > http://forums.matronics.com//files/0ef69eca_b797_45ac_828c_7cdc5f70dafb_189.jpeg > > > > > =================================== > =================================== > =================================== > =================================== > --------------------------------------------- > ________________________________ Message 2 _____________________________________ Time: 05:18:07 AM PST US Subject: Europa-List: Re: The Obsidian File - Mono Undercarriage From: "Area-51" Any aircraft undercarriage or mechanical item for that matter will fail if impacted with enough force; damage to the mono undercarriage from excessive side loaded touchdowns can be mitigated by several ways; one being thought about this afternoon may find its way into the chapter shortly... or be relegated to the graveyard of great ideas. Keep in mind the undercarriage will not lock up if the bungee tension is less than required to hold the undercarriage above its parked position; the weight of the wheel and gravity is what brings the assembly out of this scenario each time, however the force needed to close out the undercarriage remains constant. The force required to action the undercarriage through the retraction stage is not the same. Somebody mentioned about the operational over center specification; this is an adjustable setting that needs to be maintained regardless. Dave upstream there asked about how I go about doing this and what software is used... great to hear you are building a model; wishing you well with that! Regarding software; they all provide the same result; buttons are often in different places, same as politicians and beer... I use a few very special ancient tools that few these days know exactly what they each do... A piece of string is the most highly valued, next is a plumb bob, a spirit level but i have been known to use a glass of water during desperate moments, cardboard (cardboard is your best friend), protractor, calipers, a roll of masking tape, good even lighting, a clean floor, a sharp pencil, a blunt pencil, a white board marker, a rheem of plain A4 paper, an adhoc laser pointer on an adjustable tripod, a ruler and tape measure, lots and lots and lots and then some more time, lots of coffee hamburgers, about 30,000 hrs playing CAD, and about 45years of analytical experience. The model here has taken about 300 hours to measure and a further 1100 to accurately model from the data collected. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=509453#509453 ________________________________ Message 3 _____________________________________ Time: 04:45:28 PM PST US Subject: Europa-List: Anti Door Warping From: "rparigoris" Hi Area 51 Seems you kinda like uncovering Europa secrets using your computer. Perhaps you want to give a try and uncover the secret geometry of passive pin that will actually pull down the top aft edge of door. In addition, install of a passive mid door sill pin and striker that keeps door nicely in place and will prevent bulge. These two tips came from Neville. He preferred leaving the gas cylinder mount original location (compared to factory mod), reinforce corner with some CF and install passive pin. It took a number of E-Mails to get it straight in my mind precise details. After making a perfect model, got it figured. Here's a link to build: pages 19 to 26: http://www.europaowners.org/gallery2/v/Begin-06-2003/Cockpit+above+door+sills/album246/?g2_page=19 Ron P. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=509454#509454 ________________________________ Message 4 _____________________________________ Time: 05:27:05 PM PST US From: Pete Subject: Re: Europa-List: Anti Door Warping Im still planning on adding an over-center cam into the rebate to take all the compressed (closed) forces of the gas strut, totally unloading the door when closed. Just haven't got to it yet, just like my cable-handle door hinge-pins inverted escape puller :) Cheers, PeteZ > On Dec 5, 2022, at 7:51 PM, rparigoris wrote: > > > Hi Area 51 > Seems you kinda like uncovering Europa secrets using your computer. Perhaps you want to give a try and uncover the secret geometry of passive pin that will actually pull down the top aft edge of door. In addition, install of a passive mid door sill pin and striker that keeps door nicely in place and will prevent bulge. These two tips came from Neville. He preferred leaving the gas cylinder mount original location (compared to factory mod), reinforce corner with some CF and install passive pin. It took a number of E-Mails to get it straight in my mind precise details. After making a perfect model, got it figured. > Here's a link to build: pages 19 to 26: > http://www.europaowners.org/gallery2/v/Begin-06-2003/Cockpit+above+door+sills/album246/?g2_page=19 > Ron P. > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=509454#509454 > > > > > > > > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message europa-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Europa-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/europa-list Browse Digests http://www.matronics.com/digest/europa-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.