---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Sun 01/08/23: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:55 AM - Outrigger pivot wear (JDA) 2. 08:12 AM - Re: Re: ELT position and antenna (Bud Yerly) 3. 11:18 AM - Re: Re: ELT position and antenna (Pete) 4. 02:12 PM - Re: Outrigger pivot wear (h&jeuropa) 5. 04:09 PM - Re: Re: ELT position and antenna (William Daniell) ________________________________ Message 1 _____________________________________ Time: 04:55:56 AM PST US Subject: Europa-List: Outrigger pivot wear From: "JDA" Outrigger advice wanted please. I have an early kit (classic wing), and despite low hours (80ish) there is wear in the outrigger pivot. I understand the factory offered an insert. I believe there is also a MOD to address this. Anyone have any experience or advice please? Read this topic online here: http://forums.matronics.com/viewtopic.php?p=509911#509911 ________________________________ Message 2 _____________________________________ Time: 08:12:07 AM PST US From: Bud Yerly Subject: RE: Europa-List: Re: ELT position and antenna Will, I've installed the ELT antenna a number of ways. I've installed an AAE carbon fiber antenna with a splitter for a handheld a ntenna to also connect to for better backup com options. VHF only I've simply installed the whip antenna with a radial ground plane equal to the antenna length in the rear floor and a small support for the antenna ti p to prevent it from making noise. I've installed a tail mounted dipole unit onto a tail post before finishing (no com antenna near it). Normally the Artex or now discontinued AmeriKing were mostly installed belo w the baggage bay for ease of service. It was simple to run a coax to the whip antenna supplied or an AAE carbon antenna. The new 406/121.5 dual fre quency whip antenna Artex uses is supposedly good for both frequencies. Fo r VHF 121.5 the ground plane for a quarter wave is 33-36 inches but some do a half 1/4 wave so about 8.5 inches diameter, but I find the signal weak u sing a handheld vhf on 121.5 using an 8 inch circle alone. Since the Arte x 345 is a 15 inch whip antenna a simple 15 inch radius ground plane of 4-8 radials works fine. I always had to laugh at myself when explaining to a customer that placing the ELT antenna and the com also in the mid fuselage was interesting. As t he ELT only works when you crash so who cares about spacing the antennas ex cept for reflection, then if separated by 36 inches, reflection is not an i ssue. Heck in our composite aircraft I wonder if we could just use the gea r leg as part of the dipole. Some smart guy needs to look into that. Just run a couple of tapes about 30 inches long out from the hat section in the drawing I've attached, and it works. Normally I tack the legs with su perglue then lay a thin bit of glass over the fragile copper tape. Some us e a copper braid and some just run aluminum strips using aluminum tape but if using tape make sure you remove the glue at the contact points to assure a good ground. If near the side of the fuselage just run the spider web o ut one side. It still works but is a bit directional. I won't run a radiu s up the fuselage wall vertically where it can reflect back at the antenna. We don't know what direction the fuselage will end up in a crash but instal l the antenna within 20 degrees of vertical and near the fuselage centerlin e or the inspector will die of a heart attack. Best Regards, Bud Yerly My ELT is an EBC 302 121.5 and 243.0 VHF/UHF Easy to install but the alkal ine battery is expensive and can corrode destroying the unit. Replacement for a 406 model is prohibitively expensive. -----Original Message----- From: owner-europa-list-server@matronics.com On Behalf Of rparigoris Sent: Saturday, January 07, 2023 2:38 PM Subject: Europa-List: Re: ELT position and antenna Hi Will Forgot to mention, on both of our ELTs, Mfg said if their antenna wasn't us ed, unit would not be officially blessed. Both said OK to extend antenna lo cation with coax. Both suggested using a ground plane. That said won't do y ou much good if upside down. Ron P. Read this topic online here: https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fforums.ma tronics.com%2Fviewtopic.php%3Fp%3D509909%23509909&data=05%7C01%7C%7Cf27a7 42013344b0fd5b808daf0e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C63 8087172685618129%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMz IiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=M23g1t3qNRnhnLCdrA dkC4MWl6l2RThJOnYey4xbeoY%3D&reserved=0 %2Fwww.matronics.com%2FNavigator%3FEuropa-List&data=05%7C01%7C%7Cf27a7420 13344b0fd5b808daf0e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C63808 7172685618129%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiL CJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=KyRGGI8WOnVdbY8%2FRkJ 47YgUGPyi3TFpFR2RG5KHX2c%3D&reserved=0 %2Fforums.matronics.com%2F&data=05%7C01%7C%7Cf27a742013344b0fd5b808daf0e7 1d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129%7CUnkn own%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXV CI6Mn0%3D%7C3000%7C%7C%7C&sdata=Nu3VMMcAfFTvVUVRtKQIDM63%2B9RfpoS0ISblS71 XibY%3D&reserved=0 %2Fwiki.matronics.com%2F&data=05%7C01%7C%7Cf27a742013344b0fd5b808daf0e71d 73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129%7CUnknow n%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI 6Mn0%3D%7C3000%7C%7C%7C&sdata=yjVgxsCsO1%2FBmloiPZyH0XuH%2BB28ZY7xz366%2F APVTac%3D&reserved=0 F%2Fmatronics.com%2Fcontribution&data=05%7C01%7C%7Cf27a742013344b0fd5b808 daf0e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129% 7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWw iLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=fOuI7A0De0vdgtZYcpFjXeYPEnetin7eyL1 DYoYD%2F7Q%3D&reserved=0 ________________________________ Message 3 _____________________________________ Time: 11:18:01 AM PST US From: Pete Subject: Re: Europa-List: Re: ELT position and antenna Additional ELT tidbit: I have installed the Kannad Integra - with internal G PS and internal antenna - in the case when the external antenna breaks off e tc as is most common. https://www.aircraftspruce.com/search/search.php Nice unit. Cheers, PeteZ > On Jan 8, 2023, at 11:19 AM, Bud Yerly wrote: > > =EF=BBWill, > I've installed the ELT antenna a number of ways. > > I've installed an AAE carbon fiber antenna with a splitter for a handheld a ntenna to also connect to for better backup com options. VHF only > > I've simply installed the whip antenna with a radial ground plane equal to the antenna length in the rear floor and a small support for the antenna ti p to prevent it from making noise. > > I've installed a tail mounted dipole unit onto a tail post before finishin g (no com antenna near it). > > Normally the Artex or now discontinued AmeriKing were mostly installed bel ow the baggage bay for ease of service. It was simple to run a coax to the w hip antenna supplied or an AAE carbon antenna. The new 406/121.5 dual frequ ency whip antenna Artex uses is supposedly good for both frequencies. For V HF 121.5 the ground plane for a quarter wave is 33-36 inches but some do a h alf 1/4 wave so about 8.5 inches diameter, but I find the signal weak using a handheld vhf on 121.5 using an 8 inch circle alone. Since the Artex 345 i s a 15 inch whip antenna a simple 15 inch radius ground plane of 4-8 radials works fine. > > I always had to laugh at myself when explaining to a customer that placing the ELT antenna and the com also in the mid fuselage was interesting. As t he ELT only works when you crash so who cares about spacing the antennas exc ept for reflection, then if separated by 36 inches, reflection is not an iss ue. Heck in our composite aircraft I wonder if we could just use the gear l eg as part of the dipole. Some smart guy needs to look into that. > > Just run a couple of tapes about 30 inches long out from the hat section i n the drawing I've attached, and it works. Normally I tack the legs with su perglue then lay a thin bit of glass over the fragile copper tape. Some use a copper braid and some just run aluminum strips using aluminum tape but if using tape make sure you remove the glue at the contact points to assure a g ood ground. If near the side of the fuselage just run the spider web out on e side. It still works but is a bit directional. I won't run a radius up t he fuselage wall vertically where it can reflect back at the antenna. > > We don't know what direction the fuselage will end up in a crash but insta ll the antenna within 20 degrees of vertical and near the fuselage centerlin e or the inspector will die of a heart attack. > > Best Regards, > Bud Yerly > > My ELT is an EBC 302 121.5 and 243.0 VHF/UHF Easy to install but the alka line battery is expensive and can corrode destroying the unit. Replacement f or a 406 model is prohibitively expensive. > > > > -----Original Message----- > From: owner-europa-list-server@matronics.com On Behalf Of rparigoris > Sent: Saturday, January 07, 2023 2:38 PM > To: europa-list@matronics.com > Subject: Europa-List: Re: ELT position and antenna > > > Hi Will > > Forgot to mention, on both of our ELTs, Mfg said if their antenna wasn't u sed, unit would not be officially blessed. Both said OK to extend antenna lo cation with coax. Both suggested using a ground plane. That said won't do yo u much good if upside down. > > Ron P. > > > > > Read this topic online here: > > https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fforums.m atronics.com%2Fviewtopic.php%3Fp%3D509909%23509909&data=05%7C01%7C%7Cf27a7 42013344b0fd5b808daf0e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C638 087172685618129%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIi LCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=M23g1t3qNRnhnLCdrAdkC 4MWl6l2RThJOnYey4xbeoY%3D&reserved=0 > > > > > > > %2Fwww.matronics.com%2FNavigator%3FEuropa-List&data=05%7C01%7C%7Cf27a742 013344b0fd5b808daf0e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C63808 7172685618129%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLC JBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=KyRGGI8WOnVdbY8%2FRkJ47 YgUGPyi3TFpFR2RG5KHX2c%3D&reserved=0 > %2Fforums.matronics.com%2F&data=05%7C01%7C%7Cf27a742013344b0fd5b808daf0e 71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129%7CUnkn own%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVC I6Mn0%3D%7C3000%7C%7C%7C&sdata=Nu3VMMcAfFTvVUVRtKQIDM63%2B9RfpoS0ISblS71Xi bY%3D&reserved=0 > %2Fwiki.matronics.com%2F&data=05%7C01%7C%7Cf27a742013344b0fd5b808daf0e71 d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129%7CUnknow n%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6 Mn0%3D%7C3000%7C%7C%7C&sdata=yjVgxsCsO1%2FBmloiPZyH0XuH%2BB28ZY7xz366%2FAP VTac%3D&reserved=0 > F%2Fmatronics.com%2Fcontribution&data=05%7C01%7C%7Cf27a742013344b0fd5b80 8daf0e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129% 7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwi LCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=fOuI7A0De0vdgtZYcpFjXeYPEnetin7eyL1DY oYD%2F7Q%3D&reserved=0 > > > ________________________________ Message 4 _____________________________________ Time: 02:12:51 PM PST US Subject: Europa-List: Re: Outrigger pivot wear From: "h&jeuropa" We fitted this mod during our initial build and it has worked well for 1300 hours. For some reason I can't find it on the club website, so I've attached it here. I will get it on the club website too. Jim Butcher Read this topic online here: http://forums.matronics.com/viewtopic.php?p=509916#509916 Attachments: http://forums.matronics.com//files/outrigger_pivot_bearing_mod_189.pdf ________________________________ Message 5 _____________________________________ Time: 04:09:54 PM PST US From: William Daniell Subject: Re: Europa-List: Re: ELT position and antenna Bud thanks A funny thing... I have an antenna "connector" underneath the doorsill (like many things I do, I don't have an answer as to why I did this except that it seemed like a good idea at the time....). So anyway after my tank rebuild I reconnect the com to the Artex ELT whip antenna (no ground plane) and the ELT to the com antenna (AAE antenna). I had it like this for about 2 weeks. Everyone could hear me fine and I could hear traffic in Pahokee about 100m away. Back to the question at hand. I know that Artex will say that you have to use their antenna. That said I am wondering if there is a solution more in tune with our aircraft. My aircraft already has its airworthiness so no inspectors to offend* "install the antenna within 20 degrees of vertical and near the fuselage centerline or the inspector will die of a heart attack".* Do you think that this would work? https://www.kitplanes.com/elt-enlightenment/. [image: image.png] Construction details for the antenna (left). The element on the left is the classic =9Cstraight out=9D layout while the element on the righ t is how you can build it missing random structures while still remaining a good antenna. Both elements can be straight, both elements can be crooked, or it can be as shown, one straight and one crooked. Do not under any circumstances ask me what the pattern is going to look like for a crooked antenna element. How well did we match the transmitter to the antenna? At 121.5 MHz the match is about 2.5, and at 406 the match is a little better at 2.2. Either one is more than acceptable (right). *For those of you with plastic ships, a plain old half-wave (two quarter-wave elements made of half-inch copper tape 21.2 inches long ) dipole will work well. Simple, cheap, and works perfectly. You can bend it around, twist it to miss structural members or lay it out perfectly straight. Just remember that maximum radiation is at right angles to the antenna and practically none off the ends of the elements.* *The question has often been asked of me, =9CShould the ELT antenna b e mounted horizontally or vertically?=9D The answer has always been the same: If you can tell me the orientation of the crumpled remains of the fuselage in the middle of the dust cloud when you really need the ELT, I can tell you the orientation. In my experience, a random guess is every bit as good as anything else.* It sounds like I could make a zigzag antenna as long as each leg is 21.2". Perhaps the rear cabin bulkhead might be a good location. Thanks Will William Daniell LONGPORT +1 786 878 0246 On Sun, Jan 8, 2023 at 11:14 AM Bud Yerly wrote: > Will, > I've installed the ELT antenna a number of ways. > > I've installed an AAE carbon fiber antenna with a splitter for a handheld > antenna to also connect to for better backup com options. VHF only > > I've simply installed the whip antenna with a radial ground plane equal t o > the antenna length in the rear floor and a small support for the antenna > tip to prevent it from making noise. > > I've installed a tail mounted dipole unit onto a tail post before > finishing (no com antenna near it). > > Normally the Artex or now discontinued AmeriKing were mostly installed > below the baggage bay for ease of service. It was simple to run a coax t o > the whip antenna supplied or an AAE carbon antenna. The new 406/121.5 du al > frequency whip antenna Artex uses is supposedly good for both frequencies .. > For VHF 121.5 the ground plane for a quarter wave is 33-36 inches but som e > do a half 1/4 wave so about 8.5 inches diameter, but I find the signal we ak > using a handheld vhf on 121.5 using an 8 inch circle alone. Since the > Artex 345 is a 15 inch whip antenna a simple 15 inch radius ground plane of > 4-8 radials works fine. > > I always had to laugh at myself when explaining to a customer that placin g > the ELT antenna and the com also in the mid fuselage was interesting. As > the ELT only works when you crash so who cares about spacing the antennas > except for reflection, then if separated by 36 inches, reflection is not an > issue. Heck in our composite aircraft I wonder if we could just use the > gear leg as part of the dipole. Some smart guy needs to look into that. > > Just run a couple of tapes about 30 inches long out from the hat section > in the drawing I've attached, and it works. Normally I tack the legs wit h > superglue then lay a thin bit of glass over the fragile copper tape. Som e > use a copper braid and some just run aluminum strips using aluminum tape > but if using tape make sure you remove the glue at the contact points to > assure a good ground. If near the side of the fuselage just run the spid er > web out one side. It still works but is a bit directional. I won't run a > radius up the fuselage wall vertically where it can reflect back at the > antenna. > > We don't know what direction the fuselage will end up in a crash but > install the antenna within 20 degrees of vertical and near the fuselage > centerline or the inspector will die of a heart attack. > > Best Regards, > Bud Yerly > > My ELT is an EBC 302 121.5 and 243.0 VHF/UHF Easy to install but the > alkaline battery is expensive and can corrode destroying the unit. > Replacement for a 406 model is prohibitively expensive. > > > -----Original Message----- > From: owner-europa-list-server@matronics.com < > owner-europa-list-server@matronics.com> On Behalf Of rparigoris > Sent: Saturday, January 07, 2023 2:38 PM > To: europa-list@matronics.com > Subject: Europa-List: Re: ELT position and antenna > > > Hi Will > > Forgot to mention, on both of our ELTs, Mfg said if their antenna wasn't > used, unit would not be officially blessed. Both said OK to extend antenn a > location with coax. Both suggested using a ground plane. That said won't do > you much good if upside down. > > Ron P. > > > Read this topic online here: > > > https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fforums. matronics.com%2Fviewtopic.php%3Fp%3D509909%23509909&data=05%7C01%7C%7Cf27 a742013344b0fd5b808daf0e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C 638087172685618129%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2lu MzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=M23g1t3qNRnhnLCd rAdkC4MWl6l2RThJOnYey4xbeoY%3D&reserved=0 > > > %2Fwww.matronics.com > %2FNavigator%3FEuropa-List&data=05%7C01%7C%7Cf27a742013344b0fd5b808daf0 e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129%7CUn known%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJ XVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=KyRGGI8WOnVdbY8%2FRkJ47YgUGPyi3TFpFR2RG 5KHX2c%3D&reserved=0 > %2Fforums.matronics.com > %2F&data=05%7C01%7C%7Cf27a742013344b0fd5b808daf0e71d73%7C84df9e7fe9f640 afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129%7CUnknown%7CTWFpbGZsb3d8eyJ WIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7 C%7C&sdata=Nu3VMMcAfFTvVUVRtKQIDM63%2B9RfpoS0ISblS71XibY%3D&reserved=0 > %2Fwiki.matronics.com > %2F&data=05%7C01%7C%7Cf27a742013344b0fd5b808daf0e71d73%7C84df9e7fe9f640 afb435aaaaaaaaaaaa%7C1%7C0%7C638087172685618129%7CUnknown%7CTWFpbGZsb3d8eyJ WIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7 C%7C&sdata=yjVgxsCsO1%2FBmloiPZyH0XuH%2BB28ZY7xz366%2FAPVTac%3D&reserved =0 > > F%2Fmatronics.com%2Fcontribution&data=05%7C01%7C%7Cf27a742013344b0fd5b8 08daf0e71d73%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C63808717268561812 9%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1ha WwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=fOuI7A0De0vdgtZYcpFjXeYPEnetin7ey L1DYoYD%2F7Q%3D&reserved=0 > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message europa-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Europa-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/europa-list Browse Digests http://www.matronics.com/digest/europa-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.