---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Fri 05/05/23: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 01:34 AM - Re: Brake reservoir mounting - Trigear (JonathanMilbank) 2. 07:39 AM - Re: Brake reservoir mounting - Trigear (Bud Yerly) 3. 07:50 AM - Oil - Rotax - Synthetic or other (William Daniell) 4. 02:09 PM - Re: Oil - Rotax - Synthetic or other (Area-51) ________________________________ Message 1 _____________________________________ Time: 01:34:25 AM PST US Subject: Europa-List: Re: Brake reservoir mounting - Trigear From: "JonathanMilbank" Mine has no separate reservoir, only the master cylinders for finger brakes mounted inside the tunnel. See attached pictures. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=510736#510736 Attachments: http://forums.matronics.com//files/7g_eiky_finger_brakes_244.jpg http://forums.matronics.com//files/4g_eiky_finger_brakes_100.jpg http://forums.matronics.com//files/2g_eiky_finger_brakes_636.jpg http://forums.matronics.com//files/1g_eiky_finger_brakes_556.jpg ________________________________ Message 2 _____________________________________ Time: 07:39:34 AM PST US From: Bud Yerly Subject: Re: Europa-List: Brake reservoir mounting - Trigear Hi Paul, Since you are installing Matco masters, I would put the reservoir on the fi rewall. Even the Jamar benefits from the master higher up on the firewall. Reason: Maintenance. Matco prefers 5606. It is sticky and stains. Lasts forever but does absor b water from the air and should be changed out once it begins to discolor. Dot 5 silicone brake fluid is normally a nice purple or clear but if it st arts to yellow or turn slightly red, change it. If it is discolored it is contaminated with water. Dot 5 is nice to use as it doesn't stain if you d rip some. So I put the reservoir on the firewall as it is easy to get to a nd inspect on my routine 25 hour inspection/oil change. This requires me t o plumb more line to the masters. I use the =BC inch OD 1/8 ID vinyl tubin g for the reservoir line to make that chore easy as there is no pressure on the line so a simple barb fitting is all that is necessary and it won't le ak. To clean out the old fluid simply tip and drain the reservoir, then ad d fresh and pump the fluid down to a bleeder cup/container filled with flui d until the fluid is clean again. It works fine for me but does require an assistant. Bleeding from the bottom slave cylinder I can do IAW my articl e single handedly and it is excellent exercise getting up and down to drain the reservoir. If working alone, I simply undo the reservoir and let it d rain into a pan setting on the footwell, but only if I have no need for the exercise. Plummbing the Matcos does require some head scratching to make them easy to inspect/service/plumb. Just remember the reservoir should be the highest point in the brake system to operate properly. Putting the reservoir in the tunnel is OK but requires the time to get into the tunnel to check the condition and the level of the fluid. It is a bla ck hole in there, only openned on the annual normally, and you have to plac e your reservoir and line where it is easily serviced. This can be done, b ut it just requires planning. I have my fuel pumps, fuel flow and pressure senders, parking brake, stall horn, and fuel selector in there, so my hole is a bit tight on observation space. I placed my reservoir it where it can be seen (with a flashlight and some h ead cranking) on the firewall behind and offset from the fuel pressure regu lator. I should have put it on the oil tank side. Duh... Best Regards, Bud Yerly ________________________________ From: owner-europa-list-server@matronics.com on behalf of Paul McAllister Sent: Thursday, May 4, 2023 10:37 AM Subject: Europa-List: Brake reservoir mounting - Trigear Hi everyone, Do most folks mount the reservoir on the firewall, or the tunnel Paul ________________________________ Message 3 _____________________________________ Time: 07:50:52 AM PST US From: William Daniell Subject: Europa-List: Oil - Rotax - Synthetic or other Whats is the consensus on the best oil. I have used the Aeroshell sport PLUS 4 oil up to now mainly because I used AVGAS in Colombia. (Mogas was of doubtful quality.) I have since heard that lost of people use Mobil Synthetic. Any thoughts? William Daniell LONGPORT +1 786 878 0246 ________________________________ Message 4 _____________________________________ Time: 02:09:53 PM PST US Subject: Europa-List: Re: Oil - Rotax - Synthetic or other From: "Area-51" >From memory, there may be a discussion about this subject on Recreational Flyer forum site, or Rotax page on matronics. The issue with using similar motorcycle grade oils in the 912 is that they do not have additives for high altitude situations above 4000' i think it was... otherwise they worked fine; some with less burn-off between oil changes. Aeroshell also has an additive to flock lead from the oil and transport it to the reservoir. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=510742#510742 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message europa-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Europa-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/europa-list Browse Digests http://www.matronics.com/digest/europa-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.