---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Fri 10/13/23: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 11:16 AM - Bing 64 Choke Cable Terminal/bolt (phillik747) 2. 12:28 PM - Re: Bing 64 Choke Cable Terminal/bolt (rparigoris) 3. 03:08 PM - Re: Bing 64 Choke Cable Terminal/bolt (h&jeuropa) ________________________________ Message 1 _____________________________________ Time: 11:16:20 AM PST US Subject: Europa-List: Bing 64 Choke Cable Terminal/bolt From: "phillik747" Hello, I'm wondering what hardware is used to hold the choke cable to the carburetor choke lever. In the Rotax parts for the carb, it doesn't show the part I'm referring to. Below are a couple of images of what I'm talking about. I'm sure there are home-brew ways to get it working but wanted to see what works best. Thank you, Kyle -------- Kyle Europa Tri-gear (under construction) Read this topic online here: http://forums.matronics.com/viewtopic.php?p=511591#511591 ________________________________ Message 2 _____________________________________ Time: 12:28:08 PM PST US Subject: Europa-List: Re: Bing 64 Choke Cable Terminal/bolt From: "rparigoris" Hi Phil I have a 914 with type 64 carbs. The choke arm has a slot in one of the sides. The unit I have is meant for a cable with a swedged end barrel. I tried using the barrels that came with my FWF kit with no joy. For starters the OD of the barrel was too small, but that wasn't the entire story. Because using a barrel where you use a fastener to hold the cable in place has the end of the cable sticking out of one side where if you had a swedged end there would be no tail. No matter what I tried when using a barrel, 1 out of a dozen actuations the tail would get caught in the slot and not allow the choke to fully close. This is not a good thing because if choke is opened just a little at higher power settings it will make the mixture lean. I ended up making a Brass barrel out of a Hex where it in fact it now has a head. This holds thinks nicely captured where the tail can't get caught in the slot. Another builder installed a McFarland throttle cable and I think it does a similar thing (not positive) to hold the barrel inboard to keep the tail from getting hung up in the slot. Here's a link to my Type 64 install: https://1drv.ms/f/s!Ah1S270Nwg9VgeE0IvqA5O_QBKWt3g?e=aRlmfJ You probably have to copy and paste URL because for whatever reason Matronics breaks it up. Using Purple Loctite on the setscrew. Note the throttle stops on the throttle housing mounting screws. It allows adjusting idle from the cockpit. I wasn't sure how much cam action I might need so I made 2 with different offsets. Ron P. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=511592#511592 ________________________________ Message 3 _____________________________________ Time: 03:08:53 PM PST US Subject: Europa-List: Re: Bing 64 Choke Cable Terminal/bolt From: "h&jeuropa" Kyle, We use simple swivels from ACS, https://www.aircraftspruce.com/catalog/appages/wireswivels.php?clickkey=6170 If they are a little loose doesn't seem to be a problem. I think Lockwood and LEAF have similar available. Jim & Heather Read this topic online here: http://forums.matronics.com/viewtopic.php?p=511594#511594 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message europa-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Europa-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/europa-list Browse Digests http://www.matronics.com/digest/europa-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.