Today's Message Index:
----------------------
1. 07:21 AM - Re: Bing 64 Choke Cable Terminal/bolt (phillik747)
2. 07:26 AM - Re: Bing 64 Choke Cable Terminal/bolt (phillik747)
3. 06:48 PM - Re: Bing 64 Choke Cable Terminal/bolt (phillik747)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Bing 64 Choke Cable Terminal/bolt |
Hello Ron,
Impressive setup both on the cable barrel and the in cockpit idle adjustment. Might
have to see if the idle adjustment can be fitted to what I have already completed.
Also for links or images in Matronics use the following to help with posting:
Surround your image link with the bracket and img and escape with the same
but prefix with /, no quotes. [img]"link to image"[/img]
Same for links/url use [url="link of interest"]My Page[/url] Replace
My Page with whatever you want. eg: [url=https://1drv.ms/f/s%21Ah1S270Nwg9VgeE0IvqA5O_QBKWt3g?e=aRlmfJ]Ron's
One Drive Page.[/url]
Ron's One Drive Page. (https://1drv.ms/f/s%21Ah1S270Nwg9VgeE0IvqA5O_QBKWt3g?e=aRlmfJ)
However, your link and has an ! in it which this site's bbcode as a limitation
with. You have to convert punctuation to code. ! = %21 in URL formatting.
Good BBCode guide here. (https://www.phpbb.com/community/help/bbcode)
--------
Kyle
Europa Tri-gear (under construction)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=511598#511598
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Bing 64 Choke Cable Terminal/bolt |
Hello Jim,
This is exactly what I was looking for! Something simple to install. I have two
sets of choke cables, one came with the used engine with trimmed lengths (not
using) and the other with the kit. Both don't have stoppers, barrels, 'ends',
terminal, etc.... on them. I have no idea what the technical term is for it
but you get my point.
Thank you,
Kyle
--------
Kyle
Europa Tri-gear (under construction)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=511599#511599
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Bing 64 Choke Cable Terminal/bolt |
After a little more digging I found this at Leading Edge Air Foils LLC (https://www.leadingedgeairfoils.com/barrel-cable-end.html) for anyone else looking for one.
(https://www.leadingedgeairfoils.com/barrel-cable-end.html)
https://www.leadingedgeairfoils.com/barrel-cable-end.html (https://www.leadingedgeairfoils.com/barrel-cable-end.html)
--------
Kyle
Europa Tri-gear (under construction)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=511601#511601
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|