Today's Message Index:
----------------------
 
     1. 12:12 AM - Re: Ts 06 bushing (Area-51)
     2. 10:36 AM - Re: Re: Ts 06 bushing (William Daniell)
     3. 11:23 AM - Re: Re: Ts 06 bushing (William Daniell)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
12:12:00 AM PST US
Subject: 
Re: Ts 06 bushing
From: 
"Area-51" <goldsteinindustrial@gmail.com>
      
      
      If you had the stock dimensions you could have them turned up in Delrin perhaps.
      Just a thought; not sure what material the factory originals are... mine are
      a bit sloppy and rattle a bit at certain attitudes.
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=513425#513425
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
10:36:58 AM PST US
From: 
William Daniell <wdaniell.longport@gmail.com>
Subject: 
Re: Ts 06 bushing
      
      Can anyone tell me the thickness of the tube into  which the ts06 goes?.
      
      The od is 1/2"
      
      Thanks
      
      Will
      
      William Daniell
      +1 786 878 0246
      
      On Thu, Mar 28, 2024, 03:13 Area-51 <goldsteinindustrial@gmail.com> wrote:
      
      > goldsteinindustrial@gmail.com>
      >
      > If you had the stock dimensions you could have them turned up in Delrin
      > perhaps. Just a thought; not sure what material the factory originals
      > are... mine are a bit sloppy and rattle a bit at certain attitudes.
      >
      >
      > Read this topic online here:
      >
      > http://forums.matronics.com/viewtopic.php?p=513425#513425
      >
      >
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
11:23:30 AM PST US
From: 
William Daniell <wdaniell.longport@gmail.com>
Subject: 
Re: Ts 06 bushing
      
      Good to know...
      I only noticed it because i put some welding rods into the hinges which
      took up the hinge play.
      Its maybe 1/16 at the end of the trim tab
      Thanksa
      
      William Daniell
      +1 786 878 0246
      
      On Thu, Mar 28, 2024, 03:13 Area-51 <goldsteinindustrial@gmail.com> wrote:
      
      > goldsteinindustrial@gmail.com>
      >
      > If you had the stock dimensions you could have them turned up in Delrin
      > perhaps. Just a thought; not sure what material the factory originals
      > are... mine are a bit sloppy and rattle a bit at certain attitudes.
      >
      >
      > Read this topic online here:
      >
      > http://forums.matronics.com/viewtopic.php?p=513425#513425
      >
      >
      








Other Matronics Email List Services




Post A New Message
  
europa-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Europa-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/europa-list
Browse Europa-List Digests
  
http://www.matronics.com/digest/europa-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --