----------------------------------------------------------
                           Europa-List Digest Archive
                                      ---
                     Total Messages Posted Thu 03/28/24: 3
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 12:12 AM - Re: Ts 06 bushing  (Area-51)
     2. 10:36 AM - Re: Re: Ts 06 bushing  (William Daniell)
     3. 11:23 AM - Re: Re: Ts 06 bushing  (William Daniell)
 
 
 
________________________________  Message 1  _____________________________________


Time: 12:12:00 AM PST US
Subject: Europa-List: Re: Ts 06 bushing
From: "Area-51" <goldsteinindustrial@gmail.com>


If you had the stock dimensions you could have them turned up in Delrin perhaps.
Just a thought; not sure what material the factory originals are... mine are
a bit sloppy and rattle a bit at certain attitudes.


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=513425#513425


________________________________  Message 2  _____________________________________


Time: 10:36:58 AM PST US
From: William Daniell <wdaniell.longport@gmail.com>
Subject: Re: Europa-List: Re: Ts 06 bushing

Can anyone tell me the thickness of the tube into  which the ts06 goes?.

The od is 1/2"

Thanks

Will

William Daniell
+1 786 878 0246

On Thu, Mar 28, 2024, 03:13 Area-51 <goldsteinindustrial@gmail.com> wrote:

> goldsteinindustrial@gmail.com>
>
> If you had the stock dimensions you could have them turned up in Delrin
> perhaps. Just a thought; not sure what material the factory originals
> are... mine are a bit sloppy and rattle a bit at certain attitudes.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=513425#513425
>
>

________________________________  Message 3  _____________________________________


Time: 11:23:30 AM PST US
From: William Daniell <wdaniell.longport@gmail.com>
Subject: Re: Europa-List: Re: Ts 06 bushing

Good to know...
I only noticed it because i put some welding rods into the hinges which
took up the hinge play.
Its maybe 1/16 at the end of the trim tab
Thanksa

William Daniell
+1 786 878 0246

On Thu, Mar 28, 2024, 03:13 Area-51 <goldsteinindustrial@gmail.com> wrote:

> goldsteinindustrial@gmail.com>
>
> If you had the stock dimensions you could have them turned up in Delrin
> perhaps. Just a thought; not sure what material the factory originals
> are... mine are a bit sloppy and rattle a bit at certain attitudes.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=513425#513425
>
>

 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               europa-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Europa-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/europa-list
Browse Digests                   http://www.matronics.com/digest/europa-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.