Today's Message Index:
----------------------
 
     1. 11:23 AM - Re: Mono Rubber block height (dmac7)
     2. 03:35 PM - Re: Mono Rubber block height (Area-51)
     3. 03:39 PM - Re: Undercarriage Bushes - Raplacement (Area-51)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
11:23:30 AM PST US
Subject: 
Re: Mono Rubber block height
From: 
"dmac7" <dmac7@outlook.com>
      
      
      It seemed to me that the suspension block slowly compresses over time under load
      but when I removed it for a few years then put it back in, it expanded back
      ( from less than 2 1/2" ) to 3". Since then, 3 years of being loaded has it almost
      where it was again ( 2 9/16" )
        If one were to have a spare block maybe it would make sense to rotate them every
      two years and let them uncompress ?  Did anyone else notice they come back
      after being unloaded a few years?
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=515338#515338
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
03:35:13 PM PST US
Subject: 
Re: Mono Rubber block height
From: 
"Area-51" <goldsteinindustrial@gmail.com>
      
      
      This is a characteristic of polyurethane.. I use 100SH skateboard wheels on my
      forward hangar cradle; after a day or more the wheels get flat spots and expand
      true again in about 20 seconds after rolling; the rear cradle uses 70SH wheels
      and they compress more if used under the main gear but also expand true almost
      immediately.
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=515339#515339
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
03:39:28 PM PST US
Subject: 
Re: Undercarriage Bushes - Raplacement
From: 
"Area-51" <goldsteinindustrial@gmail.com>
      
      
      Thanks Jim 
      
      Has anybody tried using Manganese Bronze as a replacement to the Oilite units?
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=515340#515340
      
      








Other Matronics Email List Services




Post A New Message
  
europa-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Europa-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/europa-list
Browse Europa-List Digests
  
http://www.matronics.com/digest/europa-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --