----------------------------------------------------------
                           FEWMustang-List Digest Archive
                                      ---
                     Total Messages Posted Tue 09/16/03: 3
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 05:55 AM - Re: FEWMustang-List Digest: 6 Msgs - 09/15/03  (PolymerDesign@aol.com)
     2. 08:10 PM - Re: FEW  (Gary Gerber)
     3. 08:22 PM - Re: Re: FEWMustang-List Digest: 6 Msgs - 09/15/03  (LRE2@aol.com)
 
 
 
________________________________  Message 1  _____________________________________


Time: 05:55:05 AM PST US
From: PolymerDesign@aol.com
Subject: FEWMustang-List: Re: FEWMustang-List Digest: 6 Msgs - 09/15/03
   MIME_LONG_LINE_QP@matronics.com, NO_REAL_NAME@matronics.com

--> FEWMustang-List message posted by: PolymerDesign@aol.com

These were the caps and adaptors as supplied by FEW.  Gerber suggested a 
phenolic ring Hysoled around the inside flange end.  When the o-ring on the cap

expands  when closing  it pushes in this unsupported area.  I'm going to use 
this solution.






________________________________  Message 2  _____________________________________


Time: 08:10:55 PM PST US
From: Gary Gerber <44gn@kconline.com>
   NO_REAL_NAME@matronics.com
Subject: Re: FEWMustang-List: FEW

--> FEWMustang-List message posted by: Gary Gerber <44gn@kconline.com>

Ok sounds good I will look forward for the fuel caps.

I'm sure Ed when you ask the other builders to get on line I think they will. 
It
is exciting setting down in the evening and get your email it's just like
Christmas.  We have so many good builders who have so many great ideas that make
the job much easier.

Keep the good stuff coming.  The pic's are great.  Gary

HMS23TURBO@aol.com wrote:

> --> FEWMustang-List message posted by: HMS23TURBO@aol.com
>
> Larry,
>
> You are absolutely right, the Usher caps are standard issue. What threw me
> with Ken's question was the need to put in the receptacles; not knowing that
he
> was adding additional fillers to the two that are already in the wing.
>
> Gary, FEW owes these to you and I'll make certain that they get sent.
>
> Ed
>






________________________________  Message 3  _____________________________________


Time: 08:22:27 PM PST US
From: LRE2@aol.com
Subject: Re: FEWMustang-List: Re: FEWMustang-List Digest: 6 Msgs - 09/15/03
   MIME_LONG_LINE_QP@matronics.com, NO_REAL_NAME@matronics.com

--> FEWMustang-List message posted by: LRE2@aol.com

Ken, I assume that you are using the filler necks that come with the Usher 
caps.  If so, you have no need for an additional phenolic ring.  Hysol is a poor

choice to use in the fuel tanks, as it is soluble in gasoline and in ethanol. 
 Resin/Flox is not, so a better choice.  This is also an important 
consideration when you close your wing. Several of us, after learning of this 
charactoristic of Hysol, have been careful to lay a generous bead of Resin/Flox
on the 
tank edges of the cap strips to preclude contact of the gas with the Hysol 
bond.     LRE