Today's Message Index:
----------------------
1. 09:03 AM - For Sale - 4 First Run Millennium O-320 narrow deck cylinders (MPPalmer@aol.com)
2. 10:21 AM - Re: For Sale - 4 First Run Millennium O-320 narrow deck cylinders (frequent flyer)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | For Sale - 4 First Run Millennium O-320 narrow deck cylinders |
--> Glasair-List message posted by: MPPalmer@aol.com
I just did a top overhaul on our Glasair. Lowest cylinder was 70/80
compression, but oil consumption was a quart every 4 hours. (Still acceptable
for
many shops.) To expedite the changeout, decided to buy new cylinders. That means
I have 4 first run Superior Millennium cylinders for sale.
These are narrow deck cylinders for a Lycoming O-320. They have about 1800
gentle hours on them. Very little touch 'n' go cycles, lots of cross country
time, where we started our descents 9 miles out for every thousand feet. We
also had a "rule," - 20 inches at 20 miles. Oil changes every 35 to 40 hours,
with filter. IOW, we babied these jugs. Hottest we ever saw on climbout was #2
at 450 degrees, but after changing the baffling, got it down to 425. Cruise
temps around 325 to 350.
I'm told by everyone I called when I considered overhauling them, that
Millenniums will easily go another 2000 hours. They may only require a rehone
and
new rings. If so, I will supply four 9:1 weight matched pistons with. Or, if
you prefer, I have three 8.5:1 pistons I will include.
I've pulled the valves. They look good to me. Seats also. I can supply
photos if interested and can make some rudimentary measurements for you.
I also have a new ECi exhaust valve that I'll sell separately or include with
the set. Never been used. I nicked it at the top of the stem with a dental
pick when trying to move the keepers. All the mechanics I've shown it to say
it's fine. Also the Overhaul manual allows for 1/16" long nicks... this is
only 1/64" long, maybe 5 thousands deep, and I burnished most of it out with 400
grit production sandpaper. But I'm very conservative and ordered another one
anyway. (My partner is a gal - enough said.)
Will sell the cylinders, with valves, 9:1 pistons and wrist pins (no rocker
arms nor rocker arm covers) separately for $150, or all four for $500 as is.
(You pay shipping.)
The exhaust valve lists new for $135 (not including shipping and tax) - will
sell for $120.
Am based at Phoenix, DVT if you'd like to come by and look for yourself.
Thanks,
Mike Palmer <><
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: For Sale - 4 First Run Millennium O-320 narrow deck |
cylinders
--> Glasair-List message posted by: frequent flyer <jdhcv@yahoo.com>
Mike, before you actually let them go get back in
touch with me. Jack
--- MPPalmer@aol.com wrote:
> --> Glasair-List message posted by: MPPalmer@aol.com
>
> I just did a top overhaul on our Glasair. Lowest
> cylinder was 70/80
> compression, but oil consumption was a quart every 4
> hours. (Still acceptable for
> many shops.) To expedite the changeout, decided to
> buy new cylinders. That means
> I have 4 first run Superior Millennium cylinders for
> sale.
>
> These are narrow deck cylinders for a Lycoming
> O-320. They have about 1800
> gentle hours on them. Very little touch 'n' go
> cycles, lots of cross country
> time, where we started our descents 9 miles out for
> every thousand feet. We
> also had a "rule," - 20 inches at 20 miles. Oil
> changes every 35 to 40 hours,
> with filter. IOW, we babied these jugs. Hottest we
> ever saw on climbout was #2
> at 450 degrees, but after changing the baffling, got
> it down to 425. Cruise
> temps around 325 to 350.
>
> I'm told by everyone I called when I considered
> overhauling them, that
> Millenniums will easily go another 2000 hours. They
> may only require a rehone and
> new rings. If so, I will supply four 9:1 weight
> matched pistons with. Or, if
> you prefer, I have three 8.5:1 pistons I will
> include.
>
> I've pulled the valves. They look good to me.
> Seats also. I can supply
> photos if interested and can make some rudimentary
> measurements for you.
>
> I also have a new ECi exhaust valve that I'll sell
> separately or include with
> the set. Never been used. I nicked it at the top of
> the stem with a dental
> pick when trying to move the keepers. All the
> mechanics I've shown it to say
> it's fine. Also the Overhaul manual allows for
> 1/16" long nicks... this is
> only 1/64" long, maybe 5 thousands deep, and I
> burnished most of it out with 400
> grit production sandpaper. But I'm very
> conservative and ordered another one
> anyway. (My partner is a gal - enough said.)
>
> Will sell the cylinders, with valves, 9:1 pistons
> and wrist pins (no rocker
> arms nor rocker arm covers) separately for $150, or
> all four for $500 as is.
> (You pay shipping.)
>
> The exhaust valve lists new for $135 (not including
> shipping and tax) - will
> sell for $120.
>
> Am based at Phoenix, DVT if you'd like to come by
> and look for yourself.
>
> Thanks,
>
> Mike Palmer <><
>
>
>
> Contributions
> any other
> Forums.
>
> http://www.matronics.com/chat
>
> http://www.matronics.com/subscription
> http://www.matronics.com/FAQ/Glasair-List.htm
> http://www.matronics.com/archives
> http://www.matronics.com/photoshare
> http://www.matronics.com/emaillists
>
>
>
>
>
>
_______________________________
Declare Yourself - Register online to vote today!
http://vote.yahoo.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|