---------------------------------------------------------- Glasair-List Digest Archive --- Total Messages Posted Wed 08/27/14: 2 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:41 AM - Re: louvers on Glasair III (John Dalman) 2. 07:56 AM - GL111 heat problems (Craymondw@aol.com) ________________________________ Message 1 _____________________________________ Time: 07:41:47 AM PST US Subject: Re: Glasair-List: louvers on Glasair III From: John Dalman The rear two - 3 and 4. Pretty common. They are not bad in cruise but here in Texas, when it's hot, the cylinders get hotter than I'd like but still within limits. I just need to do a cruise climb and not a more aggressive climb. On Tue, Aug 26, 2014 at 9:49 PM, Jeff Siebenhaar wrote: > Just curious, which two cylinders ? > ------------------------------ > *From:* owner-glasair-list-server@matronics.com < > owner-glasair-list-server@matronics.com> on behalf of John Dalman < > jdalmansr@gmail.com> > *Sent:* Tuesday, August 26, 2014 6:37:59 PM > *To:* glasair-list@matronics.com > *Subject:* Re: Glasair-List: louvers on Glasair III > > Thank you for the additional information. In hot weather my oil runs > about 200 in cruise and that seems ok to me. It never goes above 215 in > climb, but two CHTs go to about 410 or 415 in climb on hot days. I am > going to put new baffles on this winter, which should help. > > Thanks again, > > John > > > On Tue, Aug 26, 2014 at 7:26 PM, Dick Gossen wrote: > >> On my airplane, the answer is yes and no. The louvers exit a lot of hot >> air from the oil cooler, but oil temp is still and always problematic. I 've >> gotten used to 210 degrees at 60% cruise power in just about any weather .. >> If I run harder, the temp comes down! Conclusion: the Glasair III was no t >> designed to fly slow. >> You might note that some III's have been modified with significantly >> larger coolers (and louvers) - I considered that, but then just decided to >> fly faster and that fixed it just fine. >> Dick Gossen >> N90GG >> >> On Aug 26, 2014, at 6:17 PM, John Dalman wrote: >> >> Do they work well? Do you get good cooling from the oil cooler? >> On Aug 26, 2014 4:12 PM, wrote: >> >>> You are correct. They are for cooling with the oil cooler. Mine came >>> with my kit from glasair. >>> >>> Sent from XFINITY Connect Mobile App >>> >>> >>> ------ Original Message ------ >>> >>> From: Bubblehead >>> To: glasair-list@matronics.com >>> Sent: August 26, 2014 at 4:00 PM >>> Subject: Glasair-List: louvers on Glasair III >>> >>> >>> At Oshkosh this year I noticed that a lot of Glasair IIIs have a louver >>> on the right side of the cowl. I don't have a Glasair - I fly an RV-8 but >>> I like to look at other people's planes and learn from them. >>> >>> What are the louvers for, and where can there be bought? I am guessing >>> they are either cooling vents so more hot air exits the cowl or are the >>> outlet for the oil cooler. >>> >>> -------- >>> John >>> Keller, TX >>> RV-8 N247TD >>> >>> >>> >>> >>> Read this topic online here: >>> >>> http://forums.matronics.com/viewtopic.php?p=429383#429383 >>> >>> >>> >>> >>> >>> >>> >>> p; -Matt Dral============ >>> >>> >>> >>> * >>> >>> target="_blank">http://www.matron tp://forums.matronics.com >>> _blank">http://www.matronics.com/contribution >>> >>> * >>> >>> * >> >> href="http://www.matronics.com/Navigator?Glasair-List ">http://www.matronhref ="http://forums.matronics.com/ ">http: //forums.matronics.com >> href="http://www.matronics.com/contribution ">http://www.matronics.com/contribution >> >> * >> >> >> >> * >> >> target="_blank">http://www.matronics.com/Navigator?Glasair-List >> tp://forums.matronics.com >> _blank">http://www.matronics.com/contribution >> >> * >> >> > * > > http://www.matronics.com/Navigator?Glasair-List > ics.com > .matronics.com/contribution > > * > > * > =========== atronics.com/Navigator?Glasair-List> =========== =========== om/contribution> =========== > > * > > ________________________________ Message 2 _____________________________________ Time: 07:56:47 AM PST US From: Craymondw@aol.com Subject: Glasair-List: GL111 heat problems By powder coating and having an additional interior ceramic heat treatment on the exhaust system you can lower bottom end exhaust temperatures up to 15 degrees. That bottom engine high temperature is absorbed by the oil coolers' body, oil lines, oil sump and intake systems. After the above was done to a home base aircraft, the aircraft's oil became so cool the mechanic had to install a pilot operated gate to get the oil up to temperature!!. ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message glasair-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Glasair-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/glasair-list Browse Digests http://www.matronics.com/digest/glasair-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.