Today's Message Index:
----------------------
1. 08:05 AM - Re: Jabiru 3300 Propeller Bolts (JAPhillipsGA@aol.com)
2. 10:19 AM - Re: Re: Jabiru 3300 Propeller Bolts (Jim Stone)
3. 11:30 AM - Re: Re: Jabiru 3300 Propeller Bolts (JAPhillipsGA@aol.com)
4. 11:31 AM - Re: Re: Jabiru 3300 Propeller Bolts (JAPhillipsGA@aol.com)
5. 03:23 PM - Jabiru 3300 Carbon Fiber Propeller prototype (Jim Stone)
6. 03:47 PM - Re: Jabiru 3300 Carbon Fiber Propeller prototype (Tom Tomlin)
7. 08:20 PM - Re: [cancercured] Stopping Smoking (Bruce Guilmette, Ph.D.)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Jabiru 3300 Propeller Bolts |
--> JabiruEngine-List message posted by: JAPhillipsGA@aol.com
Dear Jabiru Friends, I have a question on torque for the prop bolts. I have
the Jabiru FWF kit with the Sensenich wood prop that comes with the kit. The
issue is the Jabiru Installation and Maintenance manual specifies on page 94
that the prop bolts be tightened to 7 foot pounds while the Sensenich
installation manual says 15-19 foot pounds. What is correct ? I know wooden props
require a bit more observation and maintenance and damage easily at the hub so
what
is the correct torque? Hope to hear back from someone, Best regards, Bill
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Jabiru 3300 Propeller Bolts |
--> JabiruEngine-List message posted by: "Jim Stone" <jsto1@tampabay.rr.com>
The Sensenich prop should be mounted with 3/8" bolts rather then the
1/4" bolts used on the standard "Jabiru made prop". Therefore the
15-19 foot pounds is the correct value to use. Undertorque will result
in prop damage and burning ( as in smoke and charred surfaces ) so be
sure to use a good Torque wrench. To much torque will crush hub
allowing moisture to get into wood. Follow Senseniches instructions.
Jim Stone
Jabiru J450 builder.
-----Original Message-----
From: owner-jabiruengine-list-server@matronics.com
[mailto:owner-jabiruengine-list-server@matronics.com] On Behalf Of
JAPhillipsGA@aol.com
Subject: JabiruEngine-List: Re: Jabiru 3300 Propeller Bolts
--> JabiruEngine-List message posted by: JAPhillipsGA@aol.com
Dear Jabiru Friends, I have a question on torque for the prop bolts. I
have
the Jabiru FWF kit with the Sensenich wood prop that comes with the kit.
The
issue is the Jabiru Installation and Maintenance manual specifies on
page 94
that the prop bolts be tightened to 7 foot pounds while the Sensenich
installation manual says 15-19 foot pounds. What is correct ? I know
wooden props
require a bit more observation and maintenance and damage easily at the
hub so what
is the correct torque? Hope to hear back from someone, Best regards,
Bill
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Jabiru 3300 Propeller Bolts |
--> JabiruEngine-List message posted by: JAPhillipsGA@aol.com
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Jabiru 3300 Propeller Bolts |
--> JabiruEngine-List message posted by: JAPhillipsGA@aol.com
thank you Jim
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Jabiru 3300 Carbon Fiber Propeller prototype |
--> JabiruEngine-List message posted by: "Jim Stone" <jsto1@tampabay.rr.com>
FYI, I have been working with Sensenich to test a new ground adjustable
carbon fiber propeller for Jabiru 2200 and 3300 engines. This has
included both ground and flight tests of multiple configurations to
insure the strenght and safety of this new Sensenich product. They are
currently selling a similar, but not interchangable, unit for Rotax
engines.
Sensenich is currently reviewing the latest flight test data, and will
probable give the go ahead for production within a couple months. The
flight tests included instrumenting the blades and shanks with up to 16
accelerometers to measure dynamic stresses.
I currently fly a Sensenich W64ZK51 wood and fiberglass prop on my J450.
The new carbon fiber is a little smoother and faster at some settings.
A wide range of pitches will be available via the built in adjustment
index so not seperate protractor is needed during adjustments.
Oshkosh brochure indicated that the full pice will be $1525 for a prop
with a nickel leading edge.
I post an update here when I get additional data from Sensenich.
Jim Stone
Jabiru J450
Clearwater FL.
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Jabiru 3300 Carbon Fiber Propeller prototype |
--> JabiruEngine-List message posted by: "Tom Tomlin" <ThomasTomlin@comcast.net>
Jim, thank you for that report. I saw it also at Oskhosh and was impressed.
Looking forward to your next report.
Tom Tomlin
IV Speedster 3300
do not archive
----- Original Message -----
From: "Jim Stone" <jsto1@tampabay.rr.com>
Subject: JabiruEngine-List: Jabiru 3300 Carbon Fiber Propeller prototype
> --> JabiruEngine-List message posted by: "Jim Stone"
> <jsto1@tampabay.rr.com>
>
> FYI, I have been working with Sensenich to test a new ground adjustable
> carbon fiber propeller for Jabiru 2200 and 3300 engines. This has
> included both ground and flight tests of multiple configurations to
> insure the strenght and safety of this new Sensenich product. They are
> currently selling a similar, but not interchangable, unit for Rotax
> engines.
>
> Sensenich is currently reviewing the latest flight test data, and will
> probable give the go ahead for production within a couple months. The
> flight tests included instrumenting the blades and shanks with up to 16
> accelerometers to measure dynamic stresses.
>
> I currently fly a Sensenich W64ZK51 wood and fiberglass prop on my J450.
> The new carbon fiber is a little smoother and faster at some settings.
> A wide range of pitches will be available via the built in adjustment
> index so not seperate protractor is needed during adjustments.
>
> Oshkosh brochure indicated that the full pice will be $1525 for a prop
> with a nickel leading edge.
>
> I post an update here when I get additional data from Sensenich.
>
> Jim Stone
> Jabiru J450
> Clearwater FL.
>
>
>
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
List-Id: <cancercured.yahoogroups.com>
List-Unsubscribe: <mailto:cancercured-unsubscribe@yahoogroups.com>
| Subject: | RE: [cancercured] Stopping Smoking |
0.01 URI_REDIRECTOR Message has HTTP redirector URI
--> JabiruEngine-List message posted by: "Bruce Guilmette, Ph.D." <bruce@survivecancer.net>
Hate to say it, but the only way to quit is quit. Take the carton, throw it
in the trash, don't buy or borrow. The physical addiction will pass,
believe it or not. The psychological addiction will last the rest of your
life. That is the really tough part.
Prayer helps, but you must make the first step. QUIT.
Been there, done that. Quit drinking and smoking the same day, 36 years
ago. Was a nasty person to be around for about a month. Could start again
tomorrow, but will not.
Bruce Guilmette
_____
From: Zena Enlow
Thank you so much Bruce. My daughter-in-law made me a present of all the
stop smoking aids...patches, gum, printed material and a letter telling me
how much the family loved me and want to have me with them longer and that
they would do whatever necessary to support me in my smoking cessation. I
just must stop but I keep saying, "after this carton".
In the past I had a problem with alcohol...one day I looked into the sky and
said, "God, please remove the desire to drink from me...you know I don't
mean it, but do it anyway". I have not had a drink in sixteen years and have
not even been tempted. It is a true miracle. I have prayed for the desire to
smoke to be removed as well, but so far it hasn't been. I know I need to be
more determined and hopeful. I will eventually stop this horrible habit. I
hate it...I would like to smell fresh and nice one more time.
Does he tell you he loves you when he's hitting you? Abuse. Narrated by Halle Berry.
Are you digging your grave with your teeth?
Read Hundreds of Collected Cancer Testimonials and learn:
http://curezone.com/forums/fd50.asp?f=2
Learn more about cancer:
http://curezone.com/diseases/cancer/
http://curezone.com/diseases/cancer/faq.asp
You are receiving this email because you elected to subscribe to the cancercured@yahoogroups.com.
To unsubscribe from this list, simply send blank e-mail message
to: cancercured-nomail@yahoogroups.com
To post message: cancercured@yahoogroups.com
To subscribe: cancercured-subscribe@yahoogroups.com
To change status to digest: cancercured-digest@yahoogroups.com
To change status to normal: cancercured-normal@yahoogroups.com
By joining the list you agree to hold yourself FULLY responsible FOR yourself!
List Archives:
http://groups.yahoo.com/group/cancercured/messages/
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/cancercured/
<*> To unsubscribe from this group, send an email to:
cancercured-unsubscribe@yahoogroups.com
http://docs.yahoo.com/info/terms/
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|