Today's Message Index:
----------------------
1. 06:35 AM - Re: Belleville Washer (T. Graziano)
2. 08:19 AM - Re: JabiruEngine-List Digest: 1 Msgs - 07/25/06 (Chuck Deiterich)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Belleville Washer |
--> JabiruEngine-List message posted by: "T. Graziano" <tonyplane@bellsouth.net>
The washer are installed "toe to toe" i.e. ( ), under the nuts and are shown
on Jabiru dwg C009013-1. Go to Jabiru USA for their Zenith Firewall Forward
and pull up "Fit prop and spinner assy" found at
http://www.usjabiru.com/Zenith%20FWF%20Images/79.%20Fit%20Prop%20&%20Spinner%20assy.PDF.
Note: Recommend you use the torque values recommended by your prop
manufacturer vice those shown for Jab. It is my understanding that the
wood used in Australian Jab props is a little softer and therefore more
"crushable" than woods used by prop manufactures such as Sensenich.
Tony Graziano
Zodiac 601XL; N493TG - 120 hrs.
--------------------
> > Time: 02:27:44 AM PST US
> From: "jetboy" <sanson.r@xtra.co.nz>
> Subject: JabiruEngine-List: Re: Belleville Washer
>
> --> JabiruEngine-List message posted by: "jetboy" <sanson.r@xtra.co.nz>
>
> Please advise where the installation diagram is for those 12 washers? are
> they
> stacked together or opposing?
> I have been finding low torque on the bolts every 5 hrs or so and would
> have
> fitted the washers had it been known they were called for. I looked at
> all the
> downloads and my manuals and CD theres no reference there so this must
> have
> been introduced since my engine new 2 yrs ago.
>
> Thanks
>
> --------
> Ralph - CH701 / 2200a
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=49697#49697
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: JabiruEngine-List Digest: 1 Msgs - 07/25/06 |
--> JabiruEngine-List message posted by: "Chuck Deiterich" <cffd@pgrb.com>
Ralph,
I sent you a copy of the manual but the source is below.
On Jabiru CD manuals look under J Series Manual/Firewall Forward/Fit Prop&
Spinner assy.PDF
Chuck D.
N701TX
> From: "jetboy" <sanson.r@xtra.co.nz>
> Subject: JabiruEngine-List: Re: Belleville Washer
>
> --> JabiruEngine-List message posted by: "jetboy" <sanson.r@xtra.co.nz>
>
> Please advise where the installation diagram is for those 12 washers? are
they
> stacked together or opposing?
> I have been finding low torque on the bolts every 5 hrs or so and would
have
> fitted the washers had it been known they were called for. I looked at
all the
> downloads and my manuals and CD theres no reference there so this must
have
> been introduced since my engine new 2 yrs ago.
>
> Thanks
>
> --------
> Ralph - CH701 / 2200a
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|