----------------------------------------------------------
                           JabiruEngine-List Digest Archive
                                      ---
                     Total Messages Posted Wed 07/26/06: 2
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 06:35 AM - Re: Belleville Washer  (T. Graziano)
     2. 08:19 AM - Re: JabiruEngine-List Digest: 1 Msgs - 07/25/06  (Chuck Deiterich)
 
 
 
________________________________  Message 1  _____________________________________


Time: 06:35:29 AM PST US
From: "T. Graziano" <tonyplane@bellsouth.net>
Subject: JabiruEngine-List: Re: Belleville Washer

--> JabiruEngine-List message posted by: "T. Graziano" <tonyplane@bellsouth.net>

The washer are installed "toe to toe" i.e. ( ), under the nuts and are shown 
on Jabiru dwg C009013-1.  Go to Jabiru USA for their Zenith Firewall Forward 
and pull up "Fit  prop and spinner assy" found at 
http://www.usjabiru.com/Zenith%20FWF%20Images/79.%20Fit%20Prop%20&%20Spinner%20assy.PDF.

Note: Recommend you use the torque values recommended by your prop 
manufacturer vice those shown for Jab.   It is my understanding that the 
wood used in Australian Jab props is a little softer and therefore more 
"crushable" than woods used by prop manufactures such as Sensenich.

Tony Graziano
Zodiac 601XL; N493TG - 120 hrs.
--------------------
>  > Time: 02:27:44 AM PST US

> From: "jetboy" <sanson.r@xtra.co.nz>
> Subject: JabiruEngine-List: Re: Belleville Washer
>
> --> JabiruEngine-List message posted by: "jetboy" <sanson.r@xtra.co.nz>
>
> Please advise where the installation diagram is for those 12 washers? are 
> they
> stacked together or opposing?
>   I have been finding low torque on the bolts every 5 hrs or so and would 
> have
> fitted the washers had it been known they were called for.  I looked at 
> all the
> downloads and my manuals and CD theres no reference there so this must 
> have
> been introduced since my engine new 2 yrs ago.
>
> Thanks
>
> --------
> Ralph - CH701 / 2200a
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=49697#49697
>
>
> 


________________________________  Message 2  _____________________________________


Time: 08:19:11 AM PST US
From: "Chuck Deiterich" <cffd@pgrb.com>
Subject: JabiruEngine-List: Re: JabiruEngine-List Digest: 1 Msgs - 07/25/06

--> JabiruEngine-List message posted by: "Chuck Deiterich" <cffd@pgrb.com>

Ralph,
I sent you a copy of the manual but the source is below.

On Jabiru CD manuals look under J Series Manual/Firewall Forward/Fit Prop&
Spinner assy.PDF
Chuck D.
N701TX

> From: "jetboy" <sanson.r@xtra.co.nz>
> Subject: JabiruEngine-List: Re: Belleville Washer
>
> --> JabiruEngine-List message posted by: "jetboy" <sanson.r@xtra.co.nz>
>
> Please advise where the installation diagram is for those 12 washers? are
they
> stacked together or opposing?
>    I have been finding low torque on the bolts every 5 hrs or so and would
have
> fitted the washers had it been known they were called for.  I looked at
all the
> downloads and my manuals and CD theres no reference there so this must
have
> been introduced since my engine new 2 yrs ago.
>
> Thanks
>
> --------
> Ralph - CH701 / 2200a
>