Today's Message Index:
----------------------
1. 04:35 PM - EGT Probes on J3300 and Sonex (sonex293)
2. 07:32 PM - Distributor cap screws loose..2200 (Lynn Matteson)
3. 09:24 PM - Re: EGT Probes on J3300 and Sonex (Jim)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | EGT Probes on J3300 and Sonex |
I'll be mounting the Jabiru 3300 on my Sonex in the next few weeks and wanted to
see if anyone has any words of advise about where to mount the 6 EGT probes
from and EIS. The Jabiru Manual states...
"Exhaust Gas Temperature (EGT) - Nominal 650 degrees C 750 degrees C (1202 degrees
F 1382 degrees F) measured 100mm from the exhaust manifold flange."
Is there going to be any problems making this work with the Sonex exhaust system?
--
Michael Crowder
Sonex #293
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=101746#101746
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Distributor cap screws loose..2200 |
I am doing my annual (or condition inspection as it's called in
Experimental), and found the distributor cap screws loose today. It
might not be a bad idea for us engine owners to keep an eye on these
screws. Mine didn't seem to have any loctite applied to them. When I
get ready to reinstall them, I'll add some loctite to the screws, and
tighten, then apply some Sentry Seal for a quick visual check to see
if the screws loosen again. This inspection is with 237 hours on the
engine.
Lynn
Kitfox IV Speedster...Jabiru 2200
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | EGT Probes on J3300 and Sonex |
Hi Mike
If possible mount your egt probes 4" down the exhaust pipe from the head.
If 4" is not possible I feel the next most important thing is that all the
probes are the same distance down the exhaust pipe from the head to get
equal readings on your gauge. Grand Rapids said if you can mount the probes
2" to 8" from the head and will work just fine.
Hope this helps you out.
Jim McCormick
Jabiru Pacific LLC
255 W Fallbrook 202B
Fresno, Ca 93711
Ph. 559-431-1701
Fax 559-277-3231
Web www.jabirupacific.com
Email Info@jabirupacific.com
-----Original Message-----
From: owner-jabiruengine-list-server@matronics.com
[mailto:owner-jabiruengine-list-server@matronics.com]On Behalf Of sonex293
Sent: Monday, March 19, 2007 3:36 PM
Subject: JabiruEngine-List: EGT Probes on J3300 and Sonex
I'll be mounting the Jabiru 3300 on my Sonex in the next few weeks and
wanted to see if anyone has any words of advise about where to mount the 6
EGT probes from and EIS. The Jabiru Manual states...
"Exhaust Gas Temperature (EGT) - Nominal 650 degrees C " 750 degrees C
(1202 degrees F " 1382 degrees F) measured 100mm from the exhaust manifold
flange."
Is there going to be any problems making this work with the Sonex exhaust
system?
--
Michael Crowder
Sonex #293
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=101746#101746
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|