Today's Message Index:
----------------------
1. 08:30 AM - Re: exhaust screw tensions (Jim@jabirupacific.com)
2. 08:57 AM - 3300 exhaust system (Rob Turk)
3. 04:08 PM - Re: exhaust screw tensions (gary aman)
4. 05:05 PM - Re: exhaust screw tensions (Jim@jabirupacific.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | exhaust screw tensions |
Hi Marvin
Your are correct it's not listed , I would recommend 7 ft-lbs if you want to
try to get a torque wrench in there, I personally don't use torque wrench on
them go by feel.
Also use so anti-seize on the exhaust bolts when you reassemble it.
Also one other note, your engine doesn't have any exhaust gaskets, it has
conical seats on the exhaust pipe.
All 2200 engines after serial 1597 have conical exhaust seats.
Jim McCormick
Jabiru Pacific LLC
255 W Fallbrook 202B
Fresno, CA 93711
Office 559-431-1701
Fax 559-233-3676
www.jabirupacific.com
-----Original Message-----
From: owner-jabiruengine-list-server@matronics.com
[mailto:owner-jabiruengine-list-server@matronics.com]On Behalf Of Mervin
Friesen
Sent: Sunday, October 21, 2007 4:29 AM
To: jabiruengines@yahoogroups.com
Subject: JabiruEngine-List: exhaust screw tensions
Good Morning,
The Jab 2200 manual (issue 4) page 22 instructs us to check the exhaust
system, check exhaust screw tensions and gasket condition. I can't find any
values for the exhaust screw tension. Does anyone know that value or where I
can find it? How have you done this check?
Mervin Friesen
Jab 2200 #1768
http://kleefeld.hsd.ca/mefriesen/
19/10/2007 5:41 PM
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 3300 exhaust system |
Has anyone tried a non-standard exhaust system and mufflers on the 3300? In
particular I'd like to know about using two smaller mufflers like these:
http://www.aircraftspruce.com/catalog/eppages/mufler8tailpipe.php
Using two of these would allow putting the oil cooler right in line with the
airflow through the oilpan, and have two heat exchangers, one for carb heat
and one for cabin heat. Someone pointed to a Sonex galery showing that setup
but without mufflers. How much does the noise level increase by not using
mufflers?
http://www.sonexaircraft.com/images/products/sonex/sonexgallery.html
Thoughts?
Rob
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | exhaust screw tensions |
Jim
Have 2200 serial # 1295. Exhaust gaskets?
G Aman
"Jim@jabirupacific.com" <jim@jabirupacific.com> wrote: Hi Marvin
Your are correct it's not listed , I would recommend 7 ft-lbs if you want to
try to get a torque wrench in there, I personally don't use torque wrench on
them go by feel.
Also use so anti-seize on the exhaust bolts when you reassemble it.
Also one other note, your engine doesn't have any exhaust gaskets, it has conical
seats on the exhaust pipe.
All 2200 engines after serial 1597 have conical exhaust seats.
Jim McCormick
Jabiru Pacific LLC
255 W Fallbrook 202B
Fresno, CA 93711
Office 559-431-1701
Fax 559-233-3676
www.jabirupacific.com
-----Original Message-----
From: owner-jabiruengine-list-server@matronics.com [mailto:owner-jabiruengine-list-server@matronics.com]On Behalf Of Mervin Friesen
Sent: Sunday, October 21, 2007 4:29 AM
Subject: JabiruEngine-List: exhaust screw tensions
Good Morning,
The Jab 2200 manual (issue 4) page 22 instructs us to check the exhaust system,
check exhaust screw tensions and gasket condition. I can't find any
values for the exhaust screw tension. Does anyone know that value or where
I can find it? How have you done this check?
Mervin Friesen
Jab 2200 #1768
http://kleefeld.hsd.ca/mefriesen/
19/10/2007 5:41 PM
href="http://www.matronics.com/Navigator?JabiruEngine-List">http://www.matronics.com/Navigator?JabiruEngine-List href="http://forums.matronics.com">http://forums.matronics.com
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | exhaust screw tensions |
Serial # 1295 still use's exhaust gaskets.
Jim McCormick
Jabiru Pacific LLC
255 W Fallbrook 202B
Fresno, CA 93711
Office 559-431-1701
Fax 559-233-3676
www.jabirupacific.com
-----Original Message-----
From: owner-jabiruengine-list-server@matronics.com
[mailto:owner-jabiruengine-list-server@matronics.com]On Behalf Of gary aman
Sent: Monday, October 22, 2007 4:08 PM
To: jabiruengine-list@matronics.com
Subject: RE: JabiruEngine-List: exhaust screw tensions
Jim
Have 2200 serial # 1295. Exhaust gaskets?
G Aman
"Jim@jabirupacific.com" <jim@jabirupacific.com> wrote:
Hi Marvin
Your are correct it's not listed , I would recommend 7 ft-lbs if you
want to try to get a torque wrench in there, I personally don't use torque
wrench on them go by feel.
Also use so anti-seize on the exhaust bolts when you reassemble it.
Also one other note, your engine doesn't have any exhaust gaskets, it
has conical seats on the exhaust pipe.
All 2200 engines after serial 1597 have conical exhaust seats.
Jim McCormick
Jabiru Pacific LLC
255 W Fallbrook 202B
Fresno, CA 93711
Office 559-431-1701
Fax 559-233-3676
www.jabirupacific.com
-----Original Message-----
From: owner-jabiruengine-list-server@matronics.com
[mailto:owner-jabiruengine-list-server@matronics.com]On Behalf Of Mervin
Friesen
Sent: Sunday, October 21, 2007 4:29 AM
To: jabiruengines@yahoogroups.com
Subject: JabiruEngine-List: exhaust screw tensions
Good Morning,
The Jab 2200 manual (issue 4) page 22 instructs us to check the
exhaust system, check exhaust screw tensions and gasket condition. I can't
find any values for the exhaust screw tension. Does anyone know that value
or where I can find it? How have you done this check?
http://www.matronics.com/Navigator?JabiruEngine-List
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|