Today's Message Index:
----------------------
1. 10:47 AM - EGT Probes (ianwilson2)
2. 11:11 AM - Re: EGT Probes (bob noffs)
3. 11:16 AM - Re: EGT Probes (steve)
4. 12:21 PM - Re: EGT Probes (Lynn Matteson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hi All,
Been monitoring this forum for some time, but I'm now putting the final touches
to my 2200A X-Air H and I need your advice. I'm installing a Grand Rapids EIS
monitor for the 2200 and the Jab manual says to place the EGT probes 100mm from
the exhaust manifold plate. Has anyone else installed this EIS and what distance
did they use for the EGT probes?
Many thanks in advance for your time.
Ian
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p 2560#202560
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
hi ian,
i just installed last week on my 3300. 100mm isnt doable on my engine, i
think uniformity is the key, bob noffs
----- Original Message -----
From: "ianwilson2" <ianwilson2@hotmail.com>
Sent: Thursday, September 04, 2008 12:46 PM
Subject: JabiruEngine-List: EGT Probes
> <ianwilson2@hotmail.com>
>
> Hi All,
>
> Been monitoring this forum for some time, but I'm now putting the final
> touches to my 2200A X-Air H and I need your advice. I'm installing a
> Grand Rapids EIS monitor for the 2200 and the Jab manual says to place the
> EGT probes 100mm from the exhaust manifold plate. Has anyone else
> installed this EIS and what distance did they use for the EGT probes?
>
> Many thanks in advance for your time.
>
> Ian
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p 2560#202560
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I did... I installed the probes 100mm as instructed...
SW
----- Original Message -----
From: "ianwilson2" <ianwilson2@hotmail.com>
Sent: Thursday, September 04, 2008 10:46 AM
Subject: JabiruEngine-List: EGT Probes
> <ianwilson2@hotmail.com>
>
> Hi All,
>
> Been monitoring this forum for some time, but I'm now putting the final
> touches to my 2200A X-Air H and I need your advice. I'm installing a
> Grand Rapids EIS monitor for the 2200 and the Jab manual says to place the
> EGT probes 100mm from the exhaust manifold plate. Has anyone else
> installed this EIS and what distance did they use for the EGT probes?
>
> Many thanks in advance for your time.
>
> Ian
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p 2560#202560
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I use an EIS, and just like the instructions called for, I installed
my EGT probes at 100 mm from the head-to-exhaust pipe interface. I
also used a short stack of washers...about 1/8" worth...to better
center the tip of the probe within the pipe.
Lynn Matteson
Kitfox IV Speedster
Jabiru 2200, 562 hrs and almost ready to assemble the short block
Status: "Condition grounded, but determined to try." (Pink
Floyd..."Learning to Fly")
do not archive
On Sep 4, 2008, at 1:46 PM, ianwilson2 wrote:
> <ianwilson2@hotmail.com>
>
> Hi All,
>
> Been monitoring this forum for some time, but I'm now putting the
> final touches to my 2200A X-Air H and I need your advice. I'm
> installing a Grand Rapids EIS monitor for the 2200 and the Jab
> manual says to place the EGT probes 100mm from the exhaust manifold
> plate. Has anyone else installed this EIS and what distance did
> they use for the EGT probes?
>
> Many thanks in advance for your time.
>
> Ian
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p 2560#202560
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|