Today's Message Index:
----------------------
 
     1. 05:15 PM - Jab 3300 Regulator (lwhitlow)
     2. 09:55 PM - Re: Jab 3300 Regulator (Stanley Challgren)
     3. 09:58 PM - EGT Probe Installation (lwhitlow)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
05:15:03 PM PST US
Subject: 
Jab 3300 Regulator
From: 
"lwhitlow" <ldwhitlow@comcast.net>
      
      
      All
      
      Is there a mating plug for the regulator??  The terminals look like the standard
      fast-on connector would just slide right on the tabs, but a mating connector
      pigtailed out would make a cleaner installation and make regulator replacement
      easier if it ever fails
      
      Thanks
      
      Larry Whitlow
      601XL  Jab 3300
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=227930#227930
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
09:55:19 PM PST US
From: 
Stanley Challgren <challgren@mac.com>
Subject: 
Re: Jab 3300 Regulator
      
      
      Larry:
      
      Yes. there is.  I got one from Pete but I noticed in the 3300  
      Installation Video that they cut the plug off from the regulator and  
      installed the wires separately.
      
      Stan
      701/3300
      
      
      On Jan 31, 2009, at 17:59 , lwhitlow wrote:
      
      > >
      >
      > All
      >
      > Is there a mating plug for the regulator??  The terminals look like  
      > the standard fast-on connector would just slide right on the tabs,  
      > but a mating connector pigtailed out would make a cleaner  
      > installation and make regulator replacement easier if it ever fails
      >
      > Thanks
      >
      > Larry Whitlow
      > 601XL  Jab 3300
      >
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
09:58:38 PM PST US
Subject: 
EGT Probe Installation
From: 
"lwhitlow" <ldwhitlow@comcast.net>
      
      
      Ok  I'm Stumped
      
      The manual says to install the EGT Probe 100mm from the flange
      
      Since the pipe is curved where am I making this measurement?
      
      Anyone got any insight or a pic to help a feller out??
      
      Thanks
      
      Larry Whitlow
      601XL Jabiru 3300
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=227956#227956
      
      








Other Matronics Email List Services




Post A New Message
  
jabiruengine-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/JabiruEngine-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/jabiruengine-list
Browse JabiruEngine-List Digests
  
http://www.matronics.com/digest/jabiruengine-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --