----------------------------------------------------------
                           JabiruEngine-List Digest Archive
                                      ---
                     Total Messages Posted Sat 01/31/09: 3
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 05:15 PM - Jab 3300 Regulator  (lwhitlow)
     2. 09:55 PM - Re: Jab 3300 Regulator  (Stanley Challgren)
     3. 09:58 PM - EGT Probe Installation  (lwhitlow)
 
 
 
________________________________  Message 1  _____________________________________


Time: 05:15:03 PM PST US
Subject: JabiruEngine-List: Jab 3300 Regulator
From: "lwhitlow" <ldwhitlow@comcast.net>


All

Is there a mating plug for the regulator??  The terminals look like the standard
fast-on connector would just slide right on the tabs, but a mating connector
pigtailed out would make a cleaner installation and make regulator replacement
easier if it ever fails

Thanks

Larry Whitlow
601XL  Jab 3300


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=227930#227930


________________________________  Message 2  _____________________________________


Time: 09:55:19 PM PST US
From: Stanley Challgren <challgren@mac.com>
Subject: Re: JabiruEngine-List: Jab 3300 Regulator


Larry:

Yes. there is.  I got one from Pete but I noticed in the 3300  
Installation Video that they cut the plug off from the regulator and  
installed the wires separately.

Stan
701/3300


On Jan 31, 2009, at 17:59 , lwhitlow wrote:

> >
>
> All
>
> Is there a mating plug for the regulator??  The terminals look like  
> the standard fast-on connector would just slide right on the tabs,  
> but a mating connector pigtailed out would make a cleaner  
> installation and make regulator replacement easier if it ever fails
>
> Thanks
>
> Larry Whitlow
> 601XL  Jab 3300
>


________________________________  Message 3  _____________________________________


Time: 09:58:38 PM PST US
Subject: JabiruEngine-List: EGT Probe Installation
From: "lwhitlow" <ldwhitlow@comcast.net>


Ok  I'm Stumped

The manual says to install the EGT Probe 100mm from the flange

Since the pipe is curved where am I making this measurement?

Anyone got any insight or a pic to help a feller out??

Thanks

Larry Whitlow
601XL Jabiru 3300


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=227956#227956


 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               jabiruengine-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/JabiruEngine-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/jabiruengine-list
Browse Digests                   http://www.matronics.com/digest/jabiruengine-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.