Today's Message Index:
----------------------
 
     1. 12:42 AM - Re: Radio popping (jetboy)
     2. 08:13 AM - Need resistor values for oil pres and oil temp sensors. (mosquito56)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
12:42:47 AM PST US
Subject: 
Re: Radio popping
From: 
"jetboy" <sanson.r@xtra.co.nz>
      
      
      popping noises can occur due to the AC dynamo regulator. If that is the source,
      it will not be present if the AC leads are disconnected.
      
      Another clue is that this type of noise will change in nature during the charging
      of the battery. It is not troublesome if the installation is wired according
      to the advice in the Jabiru manual. Simply put this means the regulator + wires
      connect direct to battery + , regulator ground connect directly to batt ground,
      all avionics ground to common stud on firewall, headset sockets are not
      in contact with airframe (unless they are on the same metal panel as the intercom/radio)
      and the battery capacity is one of 20 amp-hours or greater.
      
      Ralph
      
      --------
      Ralph - CH701 / 2200a
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=268658#268658
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
08:13:33 AM PST US
Subject: 
Need resistor values for oil pres and oil temp sensors.
From: 
"mosquito56" <mosquito-56@hotmail.com>
      
      
      Can anyone tell me the range for the oil temp and oil pressure sensors on the jab
      3300.
      
      oil pressure      oil temperature
      o psi= ? ohms     any deg f = ? ohms
      20 psi= ? ohms   any deg f = ? ohms
      
      The specific numbers aren't important just 2 numbers each to get a line.
      
      I read that vdo has a 200 ohm spread but need top and bottom numbers.
      A place to find these numbers would be nice for various engines.
      
      Thanx
      
      --------
      Don Merritt- Laredo, Tx
        Apologies if I seem antagonistic.
        I believe in the freeflowing ideas and discussions between individuals for assistance
      in this thing we call life.
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=268688#268688
      
      








Other Matronics Email List Services




Post A New Message
  
jabiruengine-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/JabiruEngine-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/jabiruengine-list
Browse JabiruEngine-List Digests
  
http://www.matronics.com/digest/jabiruengine-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --