Today's Message Index:
----------------------
1. 12:54 PM - Re: Starting Problem (ces308)
2. 01:21 PM - Re: Starting Problem (ronlee)
3. 03:07 PM - Re: Re: Starting Problem (Pete Krotje)
4. 10:05 PM - Re: Starting Problem (ces308)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Starting Problem |
Hello all....
I have a A-2200 ser-1228 on my Kolb Mark III Xtra and I am just having this problem
on starting. Where can I find the SB on the ground strap? The one I have
on the engine is a small copper strap from the bottom of the block to the motor
mount. And Why all of a sudden the problem?? Any ideas?
chris ambrose
Kolb Mark 3 Xtra / Jabiru A-2200 ser# 1228....106 hrs on it
N327CS
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=291467#291467
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Starting Problem |
I have a Toyota pickup that will start intermittently when the big copper washer
in the solenoid does not contact the incoming and outgoing posts. Even though
it sounds like the solenoid engages with a robust click. What happens is the
contacts get burned down to a height that the washer can't make contact across
them when pulled in by the solenoid. With the solenoid engaged you should have
twelve volts coming in and the same going out, if not then there is no connection
happening in the solenoid.
--------
Ron Lee
Tucson, Arizona
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=291473#291473
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Starting Problem |
A small copper strap probably is not sufficient. You need a ground cable
from starter to airframe that is as large as the starter cable itself. #4
welding cable is the norm. The starter service bulletin and all other
bulletins can be found on Jabiru's web site www.jabiru.net.au . If your
engine has been starting ok in the past but suddenly is not then you problem
may be in another area like weak battery, corrosion in the dist caps or
rotor, old spark plugs with incorrect gap, out of spec coil to magnet gap,
etc. A little detective work goes a long way here.
Pete
-----Original Message-----
From: owner-jabiruengine-list-server@matronics.com
[mailto:owner-jabiruengine-list-server@matronics.com] On Behalf Of ces308
Sent: Tuesday, March 23, 2010 2:53 PM
Subject: JabiruEngine-List: Re: Starting Problem
Hello all....
I have a A-2200 ser-1228 on my Kolb Mark III Xtra and I am just having this
problem on starting. Where can I find the SB on the ground strap? The one I
have on the engine is a small copper strap from the bottom of the block to
the motor mount. And Why all of a sudden the problem?? Any ideas?
chris ambrose
Kolb Mark 3 Xtra / Jabiru A-2200 ser# 1228....106 hrs on it
N327CS
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=291467#291467
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Starting Problem |
Thank you all....
I will be working on it tomorrow..or should I say later this morning.I will let
you know what happens tonight..
chris ambrose
M3X/Jab A2200 106 hrs ser# 1228
N327CS
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=291526#291526
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|