Today's Message Index:
----------------------
1. 02:57 AM - Re: Voltmeter advice needed (Lynn Matteson)
2. 03:35 AM - Re: Voltmeter advice needed (Keith Pickford)
3. 06:23 AM - Re: Voltmeter advice needed (Mark Hubelbank)
4. 11:07 AM - Re: Voltmeter advice needed (Lynn Matteson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Voltmeter advice needed |
That sure sounds like it would fill the bill, Keith.I've printed out
the spec sheet and will show it to my electronics friend today. Jeez,
this even sounds like I could do the job myself....and I always
though that soldering pencils were for wood burning. : )
Lynn Matteson
Kitfox IV Speedster, taildragger
Jabiru 2200, #2062
Prince prop 64 x 30, P-tip
Electroair direct-fire ignition system
Rotec TBI-40 injection (sleeved to 36mm)
Status: flying with "Ramcharger" intake manifold...1139 hrs (since
3-27-2006)
On Jul 16, 2011, at 2:29 AM, Keith Pickford wrote:
> Have a look at this - they have several ranges available
> http://www.lascarelectronics.com/pdf-usb-datalogging/data-
> logger0599092001277713009.pdf
>
> Regards
>
> Keith
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Voltmeter advice needed |
Good luck
--- On Sat, 16/7/11, Lynn Matteson <lynnmatt@jps.net> wrote:
From: Lynn Matteson <lynnmatt@jps.net>
Subject: Re: JabiruEngine-List: Voltmeter advice needed
That sure sounds like it would fill the bill, Keith.I've printed out the sp
ec sheet and will show it to my electronics friend today. Jeez, this even s
ounds like I could do the job myself....and I always though that soldering
pencils were for wood burning. : )
Lynn Matteson
Kitfox IV Speedster, taildragger
Jabiru 2200, #2062
Prince prop 64 x 30, P-tip
Electroair direct-fire ignition system
Rotec TBI-40 injection (sleeved to 36mm)
Status: flying with "Ramcharger" intake manifold...1139 hrs (since 3-27-200
6)
On Jul 16, 2011, at 2:29 AM, Keith Pickford wrote:
> Have a look at this - they have several ranges available
> http://www.lascarelectronics.com/pdf-usb-datalogging/data-logger059909200
1277713009.pdf
>
> Regards
>
> Keith
>
>
le, List Admin.
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Voltmeter advice needed |
Lynn,
I actually did use one of these once, in 12-14V systems, it is
possible to just use a resistor voltage divider instead of a regulator,
a 470 ohm in parallel with a 10 uF 25V cap to ground and 820 ohm to
12-14V is what I remember using.
On 07/16/2011 2:29 AM, Keith Pickford wrote:
> Have a look at this - they have several ranges available
> http://www.lascarelectronics.com/pdf-usb-datalogging/data-logger0599092001277713009.pdf
>
> Regards
>
> Keith
>
>
--
Mark Hubelbank
NorthEast Monitoring
2 Clock Tower Place
Suite 555
Maynard, MA, 01754 - USA
mhubel@nemon.com
978-443-3955
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Voltmeter advice needed |
I talked to George, my electronics friend and he had the same notion
about using the lascarelectronics unit that Keith mentioned. He also
suggested that the EIS has a 5 volt wire coming from their unit which
would solve the power supply problem. This sounds like the way to go,
and George said it should cost about $10 or so. I'll order one
Monday, no doubt.
Thanks to all who helped with suggestions...it was a big help!
Lynn Matteson
Kitfox IV Speedster, taildragger
Jabiru 2200, #2062
Prince prop 64 x 30, P-tip
Electroair direct-fire ignition system
Rotec TBI-40 injection (sleeved to 36mm)
Status: flying with "Ramcharger" intake manifold...1139 hrs (since
3-27-2006)
On Jul 16, 2011, at 9:18 AM, Mark Hubelbank wrote:
> Lynn,
> I actually did use one of these once, in 12-14V systems, it is
> possible to just use a resistor voltage divider instead of a
> regulator, a 470 ohm in parallel with a 10 uF 25V cap to ground and
> 820 ohm to 12-14V is what I remember using.
>
> On 07/16/2011 2:29 AM, Keith Pickford wrote:
>> Have a look at this - they have several ranges available
>> http://www.lascarelectronics.com/pdf-usb-datalogging/data-
>> logger0599092001277713009.pdf
>>
>> Regards
>>
>> Keith
>>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|