Today's Message Index:
----------------------
1. 08:22 AM - CHT sensor Installation (AirEupora)
2. 03:13 PM - Re: CHT sensor Installation (Lance Sandford)
3. 05:10 PM - Re: CHT sensor Installation (George Andre)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | CHT sensor Installation |
I just downloaded AVDALSR085-1 and noticed that it calls out a 5/32 screw. I'm
not sure, but I think it should be a 6/32 screw. Unless there are 5/32 screws
down under! Paragraph 3.5
I'm start this mod this morning and will install 8/32 screws as that is what I
have on the shelf.
Has anybody else completed this mod?
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=437200#437200
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CHT sensor Installation |
Rick
The CHT leads that Camit supply have 8/32" thread.
See:
http://camitaeroengines.net/collections/ancillary-parts/products/engine-cht-sensor
Regards
Lance Sandford in OZ
On 19/01/15 02:21, AirEupora wrote:
>
> I just downloaded AVDALSR085-1 and noticed that it calls out a 5/32 screw. I'm
not sure, but I think it should be a 6/32 screw. Unless there are 5/32 screws
down under! Paragraph 3.5
>
> I'm start this mod this morning and will install 8/32 screws as that is what
I have on the shelf.
>
> Has anybody else completed this mod?
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=437200#437200
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CHT sensor Installation |
i used 8-32 and think 6-32 would be too flimsy.
Additionally, instead of crimping on a new ring terminal, I just punched a hole
in the fat part of the spark plug ring sensor and trimmed the excess off to a
round shape and screwed that down. Worked perfectly. I did one side a few weeks
before the other and in flying with the mixed CHT setup saw no difference in
readings from one side to the other.
George Andre, 3300 #987, St Louis Missouri.
On Sunday, January 18, 2015 5:18 PM, Lance Sandford <lsandford@westnet.com.au>
wrote:
Rick
The CHT leads that Camit supply have 8/32" thread.
See:
http://camitaeroengines.net/collections/ancillary-parts/products/engine-cht-sensor
Regards
Lance Sandford in OZ
On 19/01/15 02:21, AirEupora wrote:
>
> I just downloaded AVDALSR085-1 and noticed that it calls out a 5/32 screw. I'm
not sure, but I think it should be a 6/32 screw. Unless there are 5/32 screws
down under! Paragraph 3.5
>
> I'm start this mod this morning and will install 8/32 screws as that is what
I have on the shelf.
>
> Has anybody else completed this mod?
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=437200#437200
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|