---------------------------------------------------------- JabiruEngine-List Digest Archive --- Total Messages Posted Mon 01/29/18: 2 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:33 PM - Fuel Pressure (BobbyPaulk@comcast.net) 2. 07:21 PM - Re: Fuel Pressure (FLYaDIVE) ________________________________ Message 1 _____________________________________ Time: 05:33:50 PM PST US From: BobbyPaulk@comcast.net Subject: JabiruEngine-List: Fuel Pressure Thanks to Tim, Gary & Barry I talked to Dynon and studied the pressure problems with their other VDO senders. My sender is for 0 to 50 psi and operating at around 2 to 3.5 psi. Should have been 0 to 30 range. Dynon is using a newer transducer with 3 wires but I don't want to go back thru the firewall, remove the boot cowl on the Zodiac, run a new wire, disconnect a plug and find another pin. The very nice guy at Dynon support gave me the old VDO part number for the 0 to 30 psi sender. I found it at Summit racing before I found out that ACS also carries it. VDO 360043D is the new number. I should have it in 4 or 5 days. The old one has lasted more than 10 yrs so if I get half that on the new one I'll be happy. I'll let ya'll know if it solves the problem. Thanks again for the responses ________________________________ Message 2 _____________________________________ Time: 07:21:37 PM PST US From: FLYaDIVE Subject: Re: JabiruEngine-List: Fuel Pressure Good Going Bobby: I would go with SUMMIT RACING before I buy anything from ACS! Hey... Since re-stringing the wire through the old hole is a PITA, why not just make a new hole. Then - After you have proven the new setup cut the old wires out and plug the old hole. Barry On Mon, Jan 29, 2018 at 8:33 PM, wrote: > Thanks to Tim, Gary & Barry > I talked to Dynon and studied the pressure problems with their other VDO > senders. > My sender is for 0 to 50 psi and operating at around 2 to 3.5 psi. Should > have been 0 to 30 range. > Dynon is using a newer transducer with 3 wires but I don't want to go back > thru the firewall, remove the boot cowl on the Zodiac, run a new wire, > disconnect a plug and find another pin. > The very nice guy at Dynon support gave me the old VDO part number for the > 0 to 30 psi sender. I found it at Summit racing before I found out that ACS > also carries it. VDO 360043D is the new number. I should have it in 4 or 5 > days. > The old one has lasted more than 10 yrs so if I get half that on the new > one I'll be happy. I'll let ya'll know if it solves the problem. > > Thanks again for the responses > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message jabiruengine-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/JabiruEngine-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/jabiruengine-list Browse Digests http://www.matronics.com/digest/jabiruengine-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.