Today's Message Index:
----------------------
1. 04:35 AM - Re: KIS TR-4 Spinner (Galin Hernandez)
2. 07:55 AM - Re: KIS TR-4 Spinner (Mike Pienaar)
3. 07:56 AM - Static port (Mike Pienaar)
4. 09:08 AM - Re: Static port (Galin Hernandez)
5. 09:41 AM - Re: Static port (Kent Pyle)
6. 01:14 PM - Re: KIS TR-4 Spinner (fasilpereira)
7. 05:33 PM - Re: KIS TR-4 Spinner (Ed Hanson)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: KIS TR-4 Spinner |
FWIW I have a 12" spinner on my KIS TR-4.
On Mon, Sep 22, 2014 at 7:54 PM, Tim Yoder <ftyoder@yoderbuilt.com> wrote:
>
> I have a TR-1 and it is a little over 10" I think. You can start by
> measuring the cowl face width and height to get an idea. Is the engine
> mounted, if so, with new mounts? They sag with age, 7 to 10 years is
> usually
> the max life. If the engine is in, measure from the center of the prop
> flange to the top of the cowl. That is where you probably want the spinner
> to be flush or 1/8" high with new motor mounts. Once you know the diameter
> you can look at the options in Aircraft Spruce for a stile you like. It
> will
> take some work, you need to have a prop so you know the its thickness to
> get
> the proper front bulkhead.
>
> Tim
>
> -----Original Message-----
> From: owner-kis-list-server@matronics.com
> [mailto:owner-kis-list-server@matronics.com] On Behalf Of fasilpereira
> Sent: Monday, September 22, 2014 1:44 PM
> To: kis-list@matronics.com
> Subject: KIS-List: KIS TR-4 Spinner
>
>
> Does anybody knows what is the correct Spinner diameter to fit on a Kis
> tr-4
> cowling with rectangular air intake?
> I'm thinking on buying a Vans RV standard fiberglass Spinner, but don't
> know
> if it will fit.
>
> Thanks,
>
> Fabricio
>
> --------
> Fabricio Pereira
> Engineer / Pilot
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=430929#430929
>
>
> ---
> This email is free from viruses and malware because avast! Antivirus
> protection is active.
> http://www.avast.com
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: KIS TR-4 Spinner |
Fabricio
I have the spinner that came with my kit that I am not using so you can have
that if you need it
Thanks
Mike
----- Original Message -----
From: "fasilpereira" <fasilpereira@yahoo.com>
Sent: Monday, September 22, 2014 1:43 PM
Subject: KIS-List: KIS TR-4 Spinner
>
> Does anybody knows what is the correct Spinner diameter to fit on a Kis
> tr-4 cowling with rectangular air intake?
> I'm thinking on buying a Vans RV standard fiberglass Spinner, but don't
> know if it will fit.
>
> Thanks,
>
> Fabricio
>
> --------
> Fabricio Pereira
> Engineer / Pilot
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=430928#430928
>
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Where is a good place to put the static port on the TR4
Thanks
Mike
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Mine are (2) right behind the real seats on each side of the fuselage. No
matter where you wind up putting it, make sure you verify the accuracy at
different airspeeds. I will get pictures of the install when I get back
home next week.
On Tuesday, September 23, 2014, Mike Pienaar <mjpienaar@shaw.ca> wrote:
>
> Where is a good place to put the static port on the TR4
>
> Thanks
> Mike
>
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Mine are part of the pitot tube. Kent
From: Galin Hernandez
Sent: Tuesday, September 23, 2014 11:08 AM
Subject: Re: KIS-List: Static port
Mine are (2) right behind the real seats on each side of the fuselage.
No matter where you wind up putting it, make sure you verify the
accuracy at different airspeeds. I will get pictures of the install when
I get back home next week.
On Tuesday, September 23, 2014, Mike Pienaar <mjpienaar@shaw.ca> wrote:
Where is a good place to put the static port on the TR4
Thanks
Mike
List" target="_blank">http://www.matronics.com/Navigator?KIS-List
FORUMS -
_blank">http://forums.matronics.com
b Site -
-Matt Dralle, List Admin.
target="_blank">http://www.matronics.com/contribution
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: KIS TR-4 Spinner |
Hi guys,
first please apologize for the duplicate message. I've sent it via Mobile Phone
and don't know why that happened.
Galin,
thanks for sending your spinner dimensions. I'll measure my cowling and check
it 12" will make a nice fit.
Mike,
I'll send an email to you about your KIS spinner.
Best regards,
Fabricio
--------
Fabricio Pereira
Engineer / Pilot
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=430987#430987
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: KIS TR-4 Spinner |
I purchased an aluminum spinner from Spruce. 12-1/16" diameter BN-3 part
#0060, Forward facing flange #05-00585, 1/16" Prop spacer #10055-1,ACS
machine fee 05-04904, High polish finish. Total amount was $396. The Spruce
vendor's phone is 928-855-8613. Talk to Valerie. I would buy it again.
Happy building.
----- Original Message -----
From: "fasilpereira" <fasilpereira@yahoo.com>
Sent: Monday, September 22, 2014 3:43 PM
Subject: KIS-List: KIS TR-4 Spinner
>
> Does anybody knows what is the correct Spinner diameter to fit on a Kis
> tr-4 cowling with rectangular air intake?
> I'm thinking on buying a Vans RV standard fiberglass Spinner, but don't
> know if it will fit.
>
> Thanks,
>
> Fabricio
>
> --------
> Fabricio Pereira
> Engineer / Pilot
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=430928#430928
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|