---------------------------------------------------------- KIS-List Digest Archive --- Total Messages Posted Fri 07/08/16: 9 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 06:43 AM - Wing tip landing light (pastormac@comcast.net) 2. 07:22 AM - Re: Wing tip landing light (Bill Schertz) 3. 08:49 AM - Re: Wing tip landing light (pastormac@comcast.net) 4. 10:08 AM - Re: Wing tip landing light (Bill Schertz) 5. 11:49 AM - Re: Wing tip landing light (pastormac@comcast.net) 6. 12:50 PM - Oshkosh 2016 (Twellmann, Ralf) 7. 01:22 PM - Re: Wing tip landing light (Galin Hernandez) 8. 03:55 PM - Re: Wing tip landing light (pastormac@comcast.net) 9. 06:12 PM - Re: Wing tip landing light (Alfred Rosa) ________________________________ Message 1 _____________________________________ Time: 06:43:38 AM PST US From: pastormac@comcast.net Subject: KIS-List: Wing tip landing light Hi Guys, Can anyone suggest a wing tip landing light kit for my KIS. Or a good way to install one? I didn't want to cut into the wing. Sent from my iPhone ________________________________ Message 2 _____________________________________ Time: 07:22:33 AM PST US From: "Bill Schertz" Subject: Re: KIS-List: Wing tip landing light Check Bob Reed's website, http://www.kisbuild.r-a-reed-assoc.com/ , go to tips section, then landinhg light installation. It is how I did it, but it is in the leading edge of the wing, not the wing tip. Some of the technique might be useful to you. Bill Schertz -----Original Message----- From: pastormac@comcast.net Sent: Friday, July 08, 2016 7:43 AM Subject: KIS-List: Wing tip landing light Hi Guys, Can anyone suggest a wing tip landing light kit for my KIS. Or a good way to install one? I didn't want to cut into the wing. Sent from my iPhone ________________________________ Message 3 _____________________________________ Time: 08:49:43 AM PST US From: pastormac@comcast.net Subject: Re: KIS-List: Wing tip landing light Thanks Bill! Didn't know what tool to use to cut into the wing? I know you can't use a jig saw. I also just had the plane repainted. Sent from my iPhone > On Jul 8, 2016, at 9:22 AM, Bill Schertz wrote: > > > Check Bob Reed's website, http://www.kisbuild.r-a-reed-assoc.com/ , go to tips section, then landinhg light installation. > > It is how I did it, but it is in the leading edge of the wing, not the wing tip. Some of the technique might be useful to you. > > Bill Schertz > > -----Original Message----- From: pastormac@comcast.net > Sent: Friday, July 08, 2016 7:43 AM > To: kis-list@matronics.com > Subject: KIS-List: Wing tip landing light > > > Hi Guys, > Can anyone suggest a wing tip landing light kit for my KIS. Or a good way to install one? I didn't want to cut into the wing. > > Sent from my iPhone > > > > > > > > > ________________________________ Message 4 _____________________________________ Time: 10:08:04 AM PST US From: "Bill Schertz" Subject: Re: KIS-List: Wing tip landing light A very handy tool for fiberglass work is the FEIN oscillating head saw/sander. It oscillates the cutting tool or sanding head back and forth 2 degrees. you can touch the cutting surface with your finger and it will not cut it, but a rigid material like fiberglass it cuts very smoothly and controlled. Great for detail sanding also. Others make a similar product, such as Bosch, etc. I have the FEIN tool. -----Original Message----- From: pastormac@comcast.net Sent: Friday, July 08, 2016 9:48 AM Subject: Re: KIS-List: Wing tip landing light Thanks Bill! Didn't know what tool to use to cut into the wing? I know you can't use a jig saw. I also just had the plane repainted. Sent from my iPhone > On Jul 8, 2016, at 9:22 AM, Bill Schertz wrote: > > > Check Bob Reed's website, http://www.kisbuild.r-a-reed-assoc.com/ , go to > tips section, then landinhg light installation. > > It is how I did it, but it is in the leading edge of the wing, not the > wing tip. Some of the technique might be useful to you. > > Bill Schertz > > -----Original Message----- From: pastormac@comcast.net > Sent: Friday, July 08, 2016 7:43 AM > To: kis-list@matronics.com > Subject: KIS-List: Wing tip landing light > > > Hi Guys, > Can anyone suggest a wing tip landing light kit for my KIS. Or a good way > to install one? I didn't want to cut into the wing. > > Sent from my iPhone > > ________________________________ Message 5 _____________________________________ Time: 11:49:49 AM PST US From: pastormac@comcast.net Subject: Re: KIS-List: Wing tip landing light Thanks!!! Sent from my iPhone > On Jul 8, 2016, at 12:07 PM, Bill Schertz wrote: > > > A very handy tool for fiberglass work is the FEIN oscillating head saw/sander. It oscillates the cutting tool or sanding head back and forth 2 degrees. you can touch the cutting surface with your finger and it will not cut it, but a rigid material like fiberglass it cuts very smoothly and controlled. Great for detail sanding also. > > Others make a similar product, such as Bosch, etc. I have the FEIN tool. > > -----Original Message----- From: pastormac@comcast.net > Sent: Friday, July 08, 2016 9:48 AM > To: kis-list@matronics.com > Subject: Re: KIS-List: Wing tip landing light > > > Thanks Bill! Didn't know what tool to use to cut into the wing? I know you can't use a jig saw. I also just had the plane repainted. > > Sent from my iPhone > >> On Jul 8, 2016, at 9:22 AM, Bill Schertz wrote: >> >> >> Check Bob Reed's website, http://www.kisbuild.r-a-reed-assoc.com/ , go to tips section, then landinhg light installation. >> >> It is how I did it, but it is in the leading edge of the wing, not the wing tip. Some of the technique might be useful to you. >> >> Bill Schertz >> >> -----Original Message----- From: pastormac@comcast.net >> Sent: Friday, July 08, 2016 7:43 AM >> To: kis-list@matronics.com >> Subject: KIS-List: Wing tip landing light >> >> >> Hi Guys, >> Can anyone suggest a wing tip landing light kit for my KIS. Or a good way to install one? I didn't want to cut into the wing. >> >> Sent from my iPhone > > > > > > > > > > ________________________________ Message 6 _____________________________________ Time: 12:50:24 PM PST US From: "Twellmann, Ralf" Subject: KIS-List: Oshkosh 2016 DQpIaSBhbGwsDQoNCmkgd2lsbCBnbyB0byBPc2hrb3NoIHdpdGggbXkgZmFtaWx5IHRoaXMgeWVh ciAoMjYuSnVseSBhbmQgMjcuIEp1bHkgKQ0KV2lsbCBzb21lIG9mIHlvdSBiZSB0aGVyZSB3aXRo IHlvdXIgcGxhbmVzIHRvbz8NCldvdWxkIGJlIG5pY2UgdG8gbWVldCB3aXRoIHlvdS4NCkJlc3Qg cmVnYXJkcywNClJhbGYgVHdlbGxtYW5uLyBHZXJtYW55DQpLSVMgVFIxLUMgIzEwNA0KDQoNCg0K DQoNClZvbiBTYW1zdW5nLVRhYmxldCBnZXNlbmRldA0K ________________________________ Message 7 _____________________________________ Time: 01:22:17 PM PST US From: Galin Hernandez Subject: Re: KIS-List: Wing tip landing light FWIW I used a combination of LED lights for my airplane. The BEACON is a Red LED 14 VDC Aircraft Beacon, the Landing/Taxi/Recognition lights are AERO LED AeroSun 800 (2ea), while the Navigation/Position/Strobes are AVEO Engineering Powerburst Plus. I posted a video on YouTube with all of them working so you can see how they operate. http://www.kestrobes.com/beacon.htm http://aeroleds.com/shop/aerosun/?val=aeroleds http://www.aveoengineering.com/powerburst-plus/ https://www.youtube.com/watch?v=s2Den_xrmvg On Fri, Jul 8, 2016 at 9:43 AM, wrote: > > Hi Guys, > Can anyone suggest a wing tip landing light kit for my KIS. Or a good way > to install one? I didn't want to cut into the wing. > > Sent from my iPhone > > ________________________________ Message 8 _____________________________________ Time: 03:55:44 PM PST US From: pastormac@comcast.net Subject: Re: KIS-List: Wing tip landing light Where did you mount the landing light? Where is the video? Sent from my iPhone > On Jul 8, 2016, at 3:21 PM, Galin Hernandez wrote: > > FWIW I used a combination of LED lights for my airplane. The BEACON is a R ed LED 14 VDC Aircraft Beacon, the Landing/Taxi/Recognition lights are AERO L ED AeroSun 800 (2ea), while the Navigation/Position/Strobes are AVEO Enginee ring Powerburst Plus. I posted a video on YouTube with all of them working s o you can see how they operate. > > > http://www.kestrobes.com/beacon.htm > http://aeroleds.com/shop/aerosun/?val=aeroleds > http://www.aveoengineering.com/powerburst-plus/ > https://www.youtube.com/watch?v=s2Den_xrmvg > >> On Fri, Jul 8, 2016 at 9:43 AM, wrote: >> >> Hi Guys, >> Can anyone suggest a wing tip landing light kit for my KIS. Or a good wa y to install one? I didn't want to cut into the wing. >> >> Sent from my iPhone >> >> >> ========== >> List" target="_blank" rel="noreferrer">http://www.matronics.com/Navig ator?KIS-List >> ========== >> FORUMS - >> _blank" rel="noreferrer">http://forums.matronics.com >> ========== >> WIKI - >> lank" rel="noreferrer">http://wiki.matronics.com >> ========== >> b Site - >> -Matt Dralle, List Admin. >> target="_blank" rel="noreferrer">http://www.matronics.com/contributio n >> ========== > ________________________________ Message 9 _____________________________________ Time: 06:12:52 PM PST US Subject: Re: KIS-List: Wing tip landing light From: Alfred Rosa Wing tip lights are almost always nav lights. Taxi lts are in the leading e dges of the wings. A landing lt can be located in the bottom cowling or in a wing leading edge. I've never seen a landing lt on the wing tip. Sent from my iPhone > On Jul 8, 2016, at 6:55 PM, pastormac@comcast.net wrote: > > Where did you mount the landing light? Where is the video? > > Sent from my iPhone > >> On Jul 8, 2016, at 3:21 PM, Galin Hernandez wrote: >> >> FWIW I used a combination of LED lights for my airplane. The BEACON is a R ed LED 14 VDC Aircraft Beacon, the Landing/Taxi/Recognition lights are AERO L ED AeroSun 800 (2ea), while the Navigation/Position/Strobes are AVEO Enginee ring Powerburst Plus. I posted a video on YouTube with all of them working s o you can see how they operate. >> >> >> http://www.kestrobes.com/beacon.htm >> http://aeroleds.com/shop/aerosun/?val=aeroleds >> http://www.aveoengineering.com/powerburst-plus/ >> https://www.youtube.com/watch?v=s2Den_xrmvg >> >>> On Fri, Jul 8, 2016 at 9:43 AM, wrote: >>> >>> Hi Guys, >>> Can anyone suggest a wing tip landing light kit for my KIS. Or a good w ay to install one? I didn't want to cut into the wing. >>> >>> Sent from my iPhone >>> >>> >>> ========== >>> List" target="_blank" rel="noreferrer">http://www.matronics.com/Navi gator?KIS-List >>> ========== >>> FORUMS - >>> _blank" rel="noreferrer">http://forums.matronics.com >>> ========== >>> WIKI - >>> lank" rel="noreferrer">http://wiki.matronics.com >>> ========== >>> b Site - >>> -Matt Dralle, List Admin. >>> target="_blank" rel="noreferrer">http://www.matronics.com/contributi on >>> ========== >> ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message kis-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/KIS-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/kis-list Browse Digests http://www.matronics.com/digest/kis-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.