Today's Message Index:
----------------------
1. 05:08 AM - Re: How do you remove the flaps? (Alfred Rosa)
2. 03:56 PM - Re: How do you remove the flaps? (Galin Hernandez)
3. 06:18 PM - Re: How do you remove the flaps? (Robert Reed)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: How do you remove the flaps? |
Too bad the hinges aren=99t made of titanium. Then you wouldn=99
t have to change them.
Al
> On Jun 23, 2018, at 12:10 AM, <mike@vision499.com> <mike@vision499.com> wr
ote:
>
> For a while there I could not understand the problem.
>
> Then I realised I put nut plates on all my hinges, this makes it a breeze t
o remove and replace them, you only have to get to one side. I put a piece o
f weed eater nylon through 2 holes on the hinge and then through the holes i
n the wing and pull it together with one hand and put the screws in with the
other. Also explains why I=99m not in the air yet.
>
> Try these screws https://www.microfasteners.com/fcmxs0808-8-32-x-1-2-t15-1
00-degree-flat-head-6-lobe-drive-machine-screws-stainless.html
>
> Keep well
>
> Mike
>
> From: owner-kis-list-server@matronics.com [mailto:owner-kis-list-server@ma
tronics.com] On Behalf Of Galin Hernandez
> Sent: June 22, 2018 5:42 PM
> To: kis-list@matronics.com
> Subject: Re: KIS-List: How do you remove the flaps?
>
> THANKS! The flap hinges are in excellent shape but, since I have new ones,
I am going to replace them anyways.
>
> On Fri, Jun 22, 2018 at 6:51 PM, Robert Reed <robertr237@att.net> wrote:
>
> Disconnect the connection from handle to flap control arm then lower the f
laps by hand until control arms slip out if the channel at end of flaps. Onc
e flaps are fully down the hinges should be accessible.
>
> (My assumption was manual flaps. In my case I disconnect the flap motor an
d lower flaps. )
>
> Bob Reed
> Sent from my iPhone
>
> > On Jun 22, 2018, at 5:33 PM, Galin Hernandez <galinhdz@gmail.com> wrote:
> >
> > Can anybody post a step-by-step method to remove the flaps on a KIS4?
>
>
> =========================
============
> List" rel="noreferrer" target="_blank">http://www.matronics.com/Naviga
tor?KIS-List
> =========================
> FORUMS -
> eferrer" target="_blank">http://forums.matronics.com
> =========================
> WIKI -
> errer" target="_blank">http://wiki.matronics.com
> ==========
> b Site -
> -Matt Dralle, List Admin.
> rel="noreferrer" target="_blank">http://www.matronics.com/contribution
> =========================
>
>
>
>
>
> Virus-free. www.avast.com
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: How do you remove the flaps? |
Bob, I followed your notes and it worked perfectly. The flap hinges are in
such perfect shape I am not even going to replace them. But now I know how
to do it. THANKS!
On Sat, Jun 23, 2018 at 8:08 AM, Alfred Rosa <fredorosa@gmail.com> wrote:
> Too bad the hinges aren=99t made of titanium. Then you wouldn
=99t have to
> change them.
> Al
>
> On Jun 23, 2018, at 12:10 AM, <mike@vision499.com> <mike@vision499.com>
> wrote:
>
> For a while there I could not understand the problem.
>
>
> Then I realised I put nut plates on all my hinges, this makes it a breeze
> to remove and replace them, you only have to get to one side. I put a pie
ce
> of weed eater nylon through 2 holes on the hinge and then through the
> holes in the wing and pull it together with one hand and put the screws i
n
> with the other. Also explains why I=99m not in the air yet.
>
>
> Try these screws https://www.microfasteners.com/fcmxs0808-8-32-x-1-2-t15-
> 100-degree-flat-head-6-lobe-drive-machine-screws-stainless.html
>
>
> Keep well
>
>
> Mike
>
>
> *From:* owner-kis-list-server@matronics.com [mailto:owner-kis-list-server
@
> matronics.com <owner-kis-list-server@matronics.com>] *On Behalf Of *Galin
> Hernandez
> *Sent:* June 22, 2018 5:42 PM
> *To:* kis-list@matronics.com
> *Subject:* Re: KIS-List: How do you remove the flaps?
>
>
> THANKS! The flap hinges are in excellent shape but, since I have new ones
,
> I am going to replace them anyways.
>
>
> On Fri, Jun 22, 2018 at 6:51 PM, Robert Reed <robertr237@att.net> wrote:
>
>
> Disconnect the connection from handle to flap control arm then lower the
> flaps by hand until control arms slip out if the channel at end of flaps.
> Once flaps are fully down the hinges should be accessible.
>
> (My assumption was manual flaps. In my case I disconnect the flap motor
> and lower flaps. )
>
> Bob Reed
> Sent from my iPhone
>
> > On Jun 22, 2018, at 5:33 PM, Galin Hernandez <galinhdz@gmail.com> wrote
:
> >
> > Can anybody post a step-by-step method to remove the flaps on a KIS4?
>
>
> ========================
=============
> List" rel="noreferrer" target="_blank">http://www.
> matronics.com/Navigator?KIS-List
> ========================
===========
> FORUMS -
> eferrer" target="_blank">http://forums.matronics.com
> ========================
===========
> WIKI -
> errer" target="_blank">http://wiki.matronics.com
> ==========
> b Site -
> -Matt Dralle, List Admin.
> rel="noreferrer" target="_blank">http://www.matronics.com/contributio
n
> ========================
===========
>
>
> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm
_campaign=sig-email&utm_content=emailclient> Virus-free.
> www.avast.com
> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm
_campaign=sig-email&utm_content=emailclient>
> <#m_1148182270651327034_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: How do you remove the flaps? |
Galin
Glad that I could be some help to you.
I am making progress and I think I see a glimmer of light at the end of the t
unnel. I had the engine removed, torn down and inspected. After almost 15 ye
ars of storage the only problems found were dried seals and the preservation
oil had gummed up. They are supposed to remount the engine next week. Follo
wing that I just have about 40 hours of wiring to finish.
Oh and I still have to purchase the Dynon Skyview system and all the com sys
tem but I have prepared everything for just dropping them in. I am guessing
that about 100 hours work remain before DAR inspection and first flight.
Bob Reed
Sent from my iPhone
> On Jun 23, 2018, at 5:54 PM, Galin Hernandez <galinhdz@gmail.com> wrote:
>
> Bob, I followed your notes and it worked perfectly. The flap hinges are in
such perfect shape I am not even going to replace them. But now I know how t
o do it. THANKS!
>
>> On Sat, Jun 23, 2018 at 8:08 AM, Alfred Rosa <fredorosa@gmail.com> wrote:
>> Too bad the hinges aren=99t made of titanium. Then you wouldn
=99t have to change them.
>> Al
>>
>>> On Jun 23, 2018, at 12:10 AM, <mike@vision499.com> <mike@vision499.com> w
rote:
>>>
>>> For a while there I could not understand the problem.
>>>
>>>
>>>
>>> Then I realised I put nut plates on all my hinges, this makes it a breez
e to remove and replace them, you only have to get to one side. I put a piec
e of weed eater nylon through 2 holes on the hinge and then through the hol
es in the wing and pull it together with one hand and put the screws in with
the other. Also explains why I=99m not in the air yet.
>>>
>>>
>>>
>>> Try these screws https://www.microfasteners.com/fcmxs0808-8-32-x-1-2-t15
-100-degree-flat-head-6-lobe-drive-machine-screws-stainless.html
>>>
>>>
>>>
>>>
>>> Keep well
>>>
>>>
>>>
>>> Mike
>>>
>>>
>>>
>>> From: owner-kis-list-server@matronics.com [mailto:owner-kis-list-server@
matronics.com] On Behalf Of Galin Hernandez
>>> Sent: June 22, 2018 5:42 PM
>>> To: kis-list@matronics.com
>>> Subject: Re: KIS-List: How do you remove the flaps?
>>>
>>>
>>>
>>> THANKS! The flap hinges are in excellent shape but, since I have new one
s, I am going to replace them anyways.
>>>
>>>
>>>
>>> On Fri, Jun 22, 2018 at 6:51 PM, Robert Reed <robertr237@att.net> wrote:
>>>
>>>
>>> Disconnect the connection from handle to flap control arm then lower the
flaps by hand until control arms slip out if the channel at end of flaps. O
nce flaps are fully down the hinges should be accessible.
>>>
>>> (My assumption was manual flaps. In my case I disconnect the flap motor a
nd lower flaps. )
>>>
>>> Bob Reed
>>> Sent from my iPhone
>>>
>>> > On Jun 22, 2018, at 5:33 PM, Galin Hernandez <galinhdz@gmail.com> wrot
e:
>>> >
>>> > Can anybody post a step-by-step method to remove the flaps on a KIS4?
>>>
>>>
>>> ========================
=============
>>> List" rel="noreferrer" target="_blank">http://www.matronics.com/Navi
gator?KIS-List
>>> ========================
===========
>>> FORUMS -
>>> eferrer" target="_blank">http://forums.matronics.com
>>> ========================
===========
>>> WIKI -
>>> errer" target="_blank">http://wiki.matronics.com
>>> ==========
>>> b Site -
>>> -Matt Dralle, List Admin.
>>> rel="noreferrer" target="_blank">http://www.matronics.com/contributi
on
>>> ========================
===========
>>>
>>>
>>>
>>>
>>>
>>>
>>> Virus-free. www.avast.com
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|