Today's Message Index:
----------------------
1. 04:17 AM - Re: Oil Tank (Sjklerks@aol.com)
2. 07:04 AM - counter wieght rivets ()
3. 12:07 PM - Re: Went South (Tom Jones)
4. 12:58 PM - Quick Drain (David Steade)
5. 05:32 PM - Re: Quick Drain (akflyer)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hi Jeff, No there's no Room to lower it anymore?
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | counter wieght rivets |
I'm trying to figure out what rivets to use to attach the counter wieghts to the
flaperon spar. There is a miss print in the manual on the model 4/classic 4
speedster. It is the same miss print as on the rivets for the fuselage butt ribs.
It says to use p/n 95006- 1/8x3/8 AS. Looking at the inventory list shows
95006 as a plastic dent rivet and only 4 in the kit.The only 1/8x3/8 rivets are
in the fuselage kit and are stainless and I assume the are for the butt ribs(total
of 16).Oh, there are 4 of them in the cover and finish kit (not enough).All
the other rivets in the flaperons are aluminum so I assume that is what to
use,but no such rivets in the inventory. Leon Morris/Classic 4 (94)/50%/Flower
Mound,TX
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Don't forget that you can keep in touch with the "Kitfox list" on the Matronics web site while you travel without having email stack up. Any time you can get to a computer hooked up to the internet just go to http://forums.matronics.com/
--------
Tom Jones
Classic IV, Phase one
503 Rotax, 72 inch Two blade Warp
Ellensburg, WA
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=126038#126038
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hi
The Quick Drain in the bottom of the header tank behind the seat on my
Mk7 has developed a leak from the rubber seal. Anyone know where the
drain valves or replacement seals are available.
Regards
David Steade
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
AC Spruce has them, or just about any repair center at the local airport should
stock them. I picked 3 up at the local airport repair center for around 10.00
each if I remember right.
--------
Leonard Perry
Soldotna AK
Avid "C" / Mk IV
582 IVO IFA
Full Lotus 1260
95% complete
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=126076#126076
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|