Kitfox-List Digest Archive

Sun 10/12/08


Total Messages Posted: 2



Today's Message Index:
----------------------
 
     1. 05:43 AM - Re: 582 starter not engaging. (815TL)
     2. 06:37 PM - Series IV Horizontal Stabilizer Struts (Guy Buchanan)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 05:43:17 AM PST US
    Subject: Re: 582 starter not engaging.
    From: "815TL" <lawrenceaw@corning.com>
    Good morning all. Well, I have some good news after looking the situation over. I tried another battery, but it still would not engage. So we tore the cowling off to see what it was doing. I had someone crank it over, while I looked at it from underneath. The mounting bolts were fine, so I new that was not the problem. I looked to me, and forgive me if I use the wrong terms here, like the gear would spin forward and latch on to the flywheel, but the pack (pressure plate?) would not slide forward. There was a lot of old thick lubrication on it. I cleaned it a little, then sprayed it good with some thin lubricant. Out of 20 tries after that, it failed to engage just 2 times. So it now seems to engage 9 out of 10 times. That is a lot better than 0 out of 10 times. :) I will keep an eye on it, but I think that was the whole issue. Thank you all for all your help and information. Andrew Read this topic online here: http://forums.matronics.com/viewtopic.php?p 8355#208355


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:37:32 PM PST US
    From: Guy Buchanan <bnn@nethere.com>
    Subject: Series IV Horizontal Stabilizer Struts
    All, Anybody remember a requirement for increasing the size of the horizontal stab struts from 10-32 to 1/4-28? Bob did it for my aircraft based on ? but I can't find a reference in the SBs or SLs. It might be a series I - III issue that Bob translated to the IV. (I'm asking for another IV owner who has the small struts.) Guy Buchanan San Diego, CA K-IV 1200 / 582-C / Warp / 100% done, thanks mostly to Bob Ducar.




    Other Matronics Email List Services

  • Post A New Message
  •   kitfox-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Kitfox-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/kitfox-list
  • Browse Kitfox-List Digests
  •   http://www.matronics.com/digest/kitfox-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --