Today's Message Index:
----------------------
0. 12:35 AM - Please Make A Contribution To Support Your Lists (Matt Dralle)
1. 06:09 AM - Re: Fuel Flow Problems, Again! (Vixen, Series-5) (bjones@dmv.com)
2. 03:56 PM - Re: Stabilzer struts upgrade? (Mike Chaney)
3. 08:38 PM - starter replacement (carlisle)
4. 08:50 PM - Re: starter replacement (cschmokel)
Message 0
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Please Make A Contribution To Support Your Lists |
Dear Listers,
There is no advertising income to support the Matronics Email Lists and Forums.
The operation is supported 100% by your personal Contributions during the November
Fund
Raiser.
Please make your Contribution today to support the continued operation and upgrade
of these services. You can pick up a really nice gift for making your Contribution
too!
You may use a Credit Card or Paypal at the Matronics Contribution Site here:
http://www.matronics.com/contribution
or, you can send a personal check to the following address:
Matronics / Matt Dralle
PO Box 347
Livermore, CA 94551-0347
Thank you in advance for your generous support!
Matt Dralle
Matronics Email List and Forum Administrator
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Fuel Flow Problems, Again! (Vixen, Series-5) |
Thanks
Sent from my Verizon Wireless BlackBerry
-----Original Message-----
From: "fox5flyer" <fox5flyer@idealwifi.net>
Subject: Kitfox-List: Fuel Flow Problems, Again! (Vixen, Seri
es-5)
This is a multi-part message in MIME format.
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Stabilzer struts upgrade? |
Dave
-
I also have a four and went for years without upgrading.- However, I thin
k the compamy reccommends it and I finally chose to upgrade just so I could
quite thinking about it.
-
Mike
1996 Kitfox IV
--- On Thu, 9/3/09, Dave G <occom@ns.sympatico.ca> wrote:
From: Dave G <occom@ns.sympatico.ca>
Subject: Kitfox-List: Stabilzer struts upgrade?
HI, I am in the final steps of repairing my model IV. I notice that my ssta
b struts, supplied with a skystar/denny crossover kit from '91 have the sma
ller 3/16 attachements. Is this an issue worth attention, should I upgrade
to the 1/4" ones?
-
Dave Goddard
KF IV 1050 / 582 / Warp
=0A=0A=0A
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | starter replacement |
Anybody ever replaced their starter through the housing on the firewall? You know.
The aluminum box that comes through the firewall from the engine compartment
and contains the starter. Mine appears to have gone out on my Model 2, 582
and I don't relish removing the engine just to get at the starter.
I also don't relish paying retail price for a new starter (~$800). Any suggestions
there?
Thanks,
Chris
Sioux Falls, SD
Model 2, 582
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=271649#271649
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: starter replacement |
Chris,
Yeah, $800 is outrageous for a starter! This is what I bought (and have yet to
install):
http://www.aircraftspruce.com/catalog/eppages/skytecRX12.php
10% more torque than the HD starter with a 10% reduced current draw, all at the
same weight as stock .. and for $260 .. looks like a winner to me! Now this
is for a 912/914 so I'm not sure if it'll fit your 582 but who knows? As far
as installing it, I'm not sure - my sprag clutch broke so I've got to tear the
engine out anyway :x
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=271650#271650
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|