---------------------------------------------------------- Kitfox-List Digest Archive --- Total Messages Posted Fri 09/10/10: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:56 AM - Tailwheel steering setup (Dave G) 2. 04:40 AM - Re: the flaperon dilema (larry huntley) 3. 03:47 PM - EGT problems resolved!! (Rical26) ________________________________ Message 1 _____________________________________ Time: 02:56:53 AM PST US From: "Dave G" Subject: Kitfox-List: Tailwheel steering setup Lost a steering spring last night, scary!! I am looking for pictures and advice on the setup so I can optimize the setup when I assemble new parts. On my previous attempt I used two stretch springs that were on the aircraft when I got it, I notice most of the setups I have seen use compression springs. Anyway, I want to do it the best way I can so I'll take whatever advise I can get, thanks. Dave Goddard KF IV 1050 / 582 / Warp ________________________________ Message 2 _____________________________________ Time: 04:40:20 AM PST US From: "larry huntley" Subject: Re: Kitfox-List: the flaperon dilema Probably best to just drive out and pick it up yourself. Larry----- Original Message ----- From: Malcolm Brubaker To: kitfox-list@matronics.com Sent: Thursday, September 09, 2010 9:12 PM Subject: Kitfox-List: the flaperon dilema what would i cost to ship a 12 ft flaperon? say aprox 300 miles could you cut in half and splice it afterwords? that would ship ups or fedex at a great savings what is a good prise for one anyway? mal Malcolm Brubaker Michigan Sport Pilot Repair LSRM-A, PPC, WS (989)513-3022 ------------------------------------------------------------------------- ----- From: jridgway To: kitfox-list@matronics.com Sent: Wed, September 8, 2010 8:34:41 PM Subject: Kitfox-List: Re: Jabiru cooling questions Use the Jab cooling system. Read this topic online here: http://forums.matronicnbsp; ------------------------------------------------------------------------- ----- Checked by AVG - www.avg.com 09/09/10 02:34:00 ________________________________ Message 3 _____________________________________ Time: 03:47:12 PM PST US Subject: Kitfox-List: EGT problems resolved!! From: "Rical26" Hi all, FINALLY I resolved my EGT problem!!! After many weeks of frustrations and trying just about everything,with all your suggestions and ideas. The problems was,I have a stratomaster gauge and the EGT senders were programmed for K-type and the senders were J-type (old) so when I changed my setting to the right type....temperature when from 1225 to 1055! Now my EGT temp is just about perfect and everything is good Thanks to all of you for your suggestions Richard Read this topic online here: http://forums.matronics.com/viewtopic.php?p=312077#312077 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message kitfox-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Kitfox-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/kitfox-list Browse Digests http://www.matronics.com/digest/kitfox-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.