Today's Message Index:
----------------------
1. 07:13 AM - Rotax 912/Kitfox choke actuating system (Ben Burbridge)
2. 11:31 AM - Re: Rotax 912/Kitfox choke actuating system (Lowell Fitt)
3. 11:51 AM - figure for service letter 35 (jridgway)
4. 01:01 PM - Jabiru (larry huntley)
5. 01:44 PM - Re: Jabiru (Jim_and_Lucy Chuk)
6. 01:59 PM - Sealant for header tank fittings (Kitfox George)
7. 02:35 PM - Re: Sealant for header tank fittings (larry huntley)
8. 02:35 PM - Re: Jabiru (larry huntley)
9. 02:37 PM - Re: Sealant for header tank fittings (Vic Baker)
10. 02:56 PM - Re: Sealant for header tank fittings (Patrick Reilly)
11. 07:49 PM - Re: Jabiru (Av8r3400)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Rotax 912/Kitfox choke actuating system |
My original (1995) Kitfox kit choke knob was impossible to pull. What
aftermarket cable/knob/bellcrank systems are there for better mechnical
advantage? Thanks Ben
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Rotax 912/Kitfox choke actuating system |
Ben, I drilled a hole in the knob and threaded a key ring through it that I
could grip with one finger. The factory also has a new set-up for the
choke.
Lowell
--------------------------------------------------
From: "Ben Burbridge" <benburb@comcast.net>
Sent: Monday, September 27, 2010 7:11 AM
Subject: Kitfox-List: Rotax 912/Kitfox choke actuating system
>
> My original (1995) Kitfox kit choke knob was impossible to pull. What
> aftermarket cable/knob/bellcrank systems are there for better mechnical
> advantage? Thanks Ben
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | figure for service letter 35 |
anybody have the complete service letter 35 (with figure 1). When I downloaded
it there was no Figure 1.
thanks..jack
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=313892#313892
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hello Folks,
Are there any used Jabiru engines available? Larry
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
There was one on Barnstormers within the last week or so for $6500. Take c
are=2C Jim Chuk
> From: asq@roadrunner.com
> To: kitfox-list@matronics.com
> Subject: Kitfox-List: Jabiru
> Date: Mon=2C 27 Sep 2010 15:57:41 -0400
>
>
> Hello Folks=2C
> Are there any used Jabiru engines available? Larry
>
===========
===========
===========
===========
>
>
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Sealant for header tank fittings |
I thought I had a good sealer for the header tank plastic to fittings, BUT
as =0Ayou can see from the attached photo. The tank-has only been in use
3 months.-Any =0Aidea on the best stuff to use=0A-George=0AKitfox Sport
almost, but not yet!=0Ado not archive
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Sealant for header tank fittings |
Proseal? Larry
----- Original Message -----
From: Kitfox George
To: kitfox-list@matronics.com
Sent: Monday, September 27, 2010 4:48 PM
Subject: Kitfox-List: Sealant for header tank fittings
I thought I had a good sealer for the header tank plastic to fittings,
BUT as you can see from the attached photo. The tank has only been in
use 3 months. Any idea on the best stuff to use
George
Kitfox Sport almost, but not yet!
do not archive
-------------------------------------------------------------------------
-----
Checked by AVG - www.avg.com
09/27/10 02:34:00
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Thanx Jim. Will check. Larry
----- Original Message -----
From: Jim_and_Lucy Chuk
To: kitfox list
Sent: Monday, September 27, 2010 4:40 PM
Subject: RE: Kitfox-List: Jabiru
There was one on Barnstormers within the last week or so for $6500.
Take care, Jim Chuk
> From: asq@roadrunner.com
> To: kitfox-list@matronics.com
> Subject: Kitfox-List: Jabiru
> Date: Mon, 27 Sep 2010 15:57:41 -0400
>
<asq@roadrunner.com>
>
> Hello Folks,
> Are there any used Jabiru engines available? Larry
>====================
> _=========
>
>
>
-------------------------------------------------------------------------
-----
Checked by AVG - www.avg.com
09/27/10 02:34:00
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Sealant for header tank fittings |
Yikes! John Mcbean can point you in the right direction. Used the
sealant that came with my kit (2004 vintage) with success. Better
check those fuel tank fittings also.
Vic Baker
S7 912S Warp
Carson City, Nv
----- Original Message -----
From: Kitfox George
To: kitfox-list@matronics.com
Sent: Monday, September 27, 2010 1:48 PM
Subject: Kitfox-List: Sealant for header tank fittings
I thought I had a good sealer for the header tank plastic to fittings,
BUT as you can see from the attached photo. The tank has only been in
use 3 months. Any idea on the best stuff to use
George
Kitfox Sport almost, but not yet!
do not archive
Message 10
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Sealant for header tank fittings |
George, The absolute best sealer for that application is Dow 730 Aircraft
Spruce p/n: 09-00383. I finally broke down and bought a tube and haven't had
a leak since. The only draw back is cost. It's over a $100 for a 3 oz
tube with shipping. I keep it in the
refrigerator and hope it lasts. Someone on this list recommended it. I tried
everything else 1st.
Pat Reilly
Mod 3 582 REBUILT again
Rockford, IL
On Mon, Sep 27, 2010 at 3:48 PM, Kitfox George <kitfoxsport@verizon.net>wrote:
> I thought I had a good sealer for the header tank plastic to fittings,
> BUT as you can see from the attached photo. The tank has only been in use 3
> months. Any idea on the best stuff to use
>
> George
> Kitfox Sport almost, but not yet!
> do not archive
>
--
Pat Reilly
Mod 3 582 Rebuild
Rockford,IL
Message 11
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Contact Dholly on Team Kitfox or Avidfoxflyers. I think he may have a 2200 for
sale.
--------
Thanks,
Av8r3400
Kitfox Model IV-1200 W/912UL & IVO
Kitfox Model IV-1050 W/912UL & Warp
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=313949#313949
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|