---------------------------------------------------------- Kitfox-List Digest Archive --- Total Messages Posted Mon 07/23/12: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 08:44 AM - Re: 912 ignition module (SkySteve) 2. 09:31 AM - Re: Re: 912 ignition module (kerrjohna@comcast.net) 3. 12:44 PM - 912ULS, WD Prop, EIS and accessories for sale (Jason Omelchuck) ________________________________ Message 1 _____________________________________ Time: 08:44:57 AM PST US Subject: Kitfox-List: Re: 912 ignition module From: "SkySteve" John, Are you back in the air? -------- Steve Wilson Huntsville, UT Kitfox Model 1- 85DD 912A / 3 Blade Warp Drive Convertible Nosewheel & Tailwheel Read this topic online here: http://forums.matronics.com/viewtopic.php?p=378986#378986 ________________________________ Message 2 _____________________________________ Time: 09:31:49 AM PST US From: kerrjohna@comcast.net Subject: Re: Kitfox-List: Re: 912 ignition module No!=C2- I will relate my problems here for any who may have insight.=C2 - The dealer tech support is stumped and has bumped the problem up to the distributor. I have gone back through the process of elimination and will try to summari ze the experience. =C2- *1000 rpm drop when right ignition switch is down. =C2- no change in rpm with both ignitions switches up when top plug in 3 & 4 is removed *4-5 omh reading on each ignition coil *swap connectors at ignition coil =C2-no change in rpm with both ignitions switches up when=C2-bottom plu g in 3 & 4 is removed *swap connectors at ignition modules =C2-1000 rpm drop when left ignition switch is down. =C2-no change in rpm with both ignitions switches up when top plug in=C2 -1 & 2=C2-is removed =C2- This seems to eliminate ignition coils and the trigger coils because of the shift to 1 & 2. Also, faulty spark plug wires seem to be eliminated. =C2- Does anything other than an ignition module come to mind? Replacing and circa 1994 engine with a 2012 model was not the "plug and pla y" exercise anticipated.=C2- The forward upper mounting lugs have been re located about 1/8" which required new/reworked motor mount components.=C2 - There is now a fuel return line requiring new plumbing from fuel pressu re line back to header tank. Arlington came along about the time this summary was submitted, now we are in the midst of OSH so it is unlikely that anything will come back for anot her week or two at best. Anxious to get the trusty bird back into the air. suggestions, comments will be appreciated. John Kerr Classic IV 800+ ttaf, 0hrs 912ul inop Logan UT ----- Original Message ----- From: "SkySteve" Sent: Monday, July 23, 2012 9:44:19 AM Subject: Kitfox-List: Re: 912 ignition module John, Are you back in the air? -------- Steve Wilson Huntsville, UT Kitfox Model 1- 85DD 912A / 3 Blade Warp Drive Convertible Nosewheel & Tailwheel Read this topic online here: http://forums.matronics.com/viewtopic.php?p=378986#378986 =========== =========== MS - =========== e - =C2- =C2- =C2- =C2- =C2--Matt Dralle, List Admin. =========== ________________________________ Message 3 _____________________________________ Time: 12:44:34 PM PST US Subject: Kitfox-List: 912ULS, WD Prop, EIS and accessories for sale From: "Jason Omelchuck" Hello All, I have a Rotax 912 ULS for Sale (275hours S/N 5643227). It comes with a Warp Drive Taper Tip 68" 3 bladed propeller (pusher for the 912), oil tank and oil tank bracket, Grand Rapids EIS (4EGT, 2CHT, Airspeed, Altimeter, fuel flow, VSI, RPM, Oil press, Oil Temp,), Coolant Overflow tank, 4" prop extension, Rotax Radiator (not in picture), Rotax oil cooler (not in picture), Carb Balancing tool, Rotax tool kit, Voltage regulator, Engine log, engine operators manual, The engine came off of an Aeroprakt A20 which I had a little landing accident in. The prop never touched anything and the engine was happily idling and had to be shut down after the accident. I am asking $16,000 for the whole lot. The prop would not be useful on a Kit Fox because it is a pusher for the 912. Make me an offer without the prop. Jason Read this topic online here: http://forums.matronics.com/viewtopic.php?p=379010#379010 Attachments: http://forums.matronics.com//files/k7a2515006dc0b_1000036_192.jpg ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message kitfox-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Kitfox-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/kitfox-list Browse Digests http://www.matronics.com/digest/kitfox-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.