Today's Message Index:
----------------------
1. 12:38 PM - Re: SS7 rudder pedal install question (Lynn Matteson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: SS7 rudder pedal install question |
26W???? That's practically my backyard....do I know you, Mike? I fly
in there from time to time with my orange Kitfox IV, and have done so
on wheels and skis. I didn't know there was a Kitfox being built in
the area.
Lynn Matteson
Kitfox IV Speedster, taildragger
Jabiru 2200, #2062
Prince prop 64 x 30, P-tip
Electroair direct-fire ignition system
Rotec TBI-40 injection (sleeved to 36mm)
Status: flying with 1430 hrs... (since 3-27-2006)
On May 7, 2013, at 11:02 PM, Michael Kraus wrote:
> <n223rv@wolflakeairport.net>
>
> Hi Lloyd,
>
> Thanks for the reply. I am going to sand off the paint and install
> the bushings, but from looking at it, it doesn't appear the bushing
> will give me enough spacing. Maybe once I assemble it, it will
> become more clear.
>
> Where in northern Mi are you? I'm at 26W near Jackson.
>
> -Mike Kraus
> RV-4 sold :-(
> RV-10 flying :-)
> KitFox SS7 Radial building :-)
>
> On May 7, 2013, at 10:29 PM, "Lloyd & Lorrie Cudnohufsky"
> <7suds@Chartermi.net> wrote:
>
>> <7suds@chartermi.net>
>>
>> Mike,
>> Not sure if anyone has had an opportunity to help you yet, I am in
>> the
>> middle of replacing my rudder cables on my Model 5, so I am
>> working with the
>> very items you have concern with. I will snap a shot of my
>> standoffs for the
>> pulleys next time I'm at the hanger. From what I remember, my
>> screw heads
>> have clearance and the only difference from your pic is the
>> bushing you have
>> laying in front of your shaft is installed on mine and seems to
>> help create
>> the separation you are looking for.
>>
>> Lloyd C KF 5 Outback
>> 912ul IVO IFA Northern Mi
>>
>>
>> -----Original Message-----
>> From: owner-kitfox-list-server@matronics.com
>> [mailto:owner-kitfox-list-server@matronics.com] On Behalf Of
>> Michael Kraus
>> Sent: Friday, May 03, 2013 6:32 PM
>> To: kitfox-list@matronics.com
>> Subject: Kitfox-List: SS7 rudder pedal install question
>>
>> I am building a SS7 and am getting ready to fab and install the
>> adjustable
>> rudder pedals. One question I have while reading the plans, I
>> don't see how
>> you space the inboard pedal so the 2 bolts holding the adjustable
>> pedal
>> control wheels do not contact each other. It seems that the bolt
>> heads will
>> hit after you install the plastic bushings and drill the assembly
>> to keep
>> your 1/32" side to side clearance.
>>
>> What am I missing? Picture attached.
>>
>> Thanks
>>
>> -Mike Kraus
>> RV-4 sold :-(
>> RV-10 flying :-)
>> KitFox SS7 Radial building :-)
>>
>>
>>
>>
>>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|