---------------------------------------------------------- Kolb-List Digest Archive --- Total Messages Posted Mon 10/24/05: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:46 AM - Re: Storm (N27SB@aol.com) 2. 08:59 AM - fuses (b young) 3. 12:57 PM - Re: Smiling Weather Gods (Jim Ballenger) 4. 04:37 PM - Re: Smiling Weather Gods (Cat36Fly@aol.com) 5. 05:00 PM - Re: EIS (Kolbdriver) ________________________________ Message 1 _____________________________________ Time: 02:46:59 AM PST US From: N27SB@aol.com Subject: Re: Kolb-List: Storm --> Kolb-List message posted by: N27SB@aol.com In a message dated 10/24/2005 12:53:33 A.M. Eastern Standard Time, biglar@gogittum.com writes: Good Luck to all you guys in south and central Florida over the next couple of days. Looks like you're in for a bit o' a blow. Yup, Time to play "Hide The Firefly" steve do not archive ________________________________ Message 2 _____________________________________ Time: 08:59:46 AM PST US From: "b young" Subject: Kolb-List: fuses --> Kolb-List message posted by: "b young" > What size circuit breaker is required for the facet fuel pump? What > size circuit beaker is required for the alternator on the 912s or is > one required? Every plane I have flow has one but I can't find any > info in the Rotax owners manual. What type sender is required for a > low fuel pressure sender for the EIS? What size is everone using for > the main circuit breaker? What size is every one using for the > radios? I will be running hand held,GPS & intercon. this has been MY rule of thumb I try to put my electrical loads between 50 % and 75 % of the fuse rating.... example 1: a 3 amp fuse" 3 x .5 1.5 3 x .75 2.25 the protected circut should be between 1.5 and 2.25 amps. Example 2: starting with a circut that uses 2.75 amps 2.75 / .5 5.5 2.75 / .75 3.67 fuse for 2.75 amp load should be between 3.67 and 5.5 amps. I would use a 5 amp.... Example 3: fuse for an altinator that produces 60 watts. since watts amps x volts.... devide 60 watts by 12 volts and you have 5 amps max output..... 5 / .5 10 5 / .75 6.67 the fuse should be between 6.67 and 10 putting a fuse on a radio is exactly the same only different a radio will show 2 amp ratings.... 1 for listening, and 1 for transmitting...... the fuse has to be large enough to handle the transmitting loads. maybe someone elce has a different idea.... and if the manufacture of a device makes a recomendation, follow it. 1 more item that i could cover: some devices have an inrush current that is different than the steady state amp draw... the best way to protect these devices is to put in a "slow blow" fuse... these fuses will usually allow double the rated amp for 1 to 2 seconds before they blow.... anything more than double the rating will blow it instantly and and anything over the rating for longer than a couple of seconds will blow it... boyd do archive ________________________________ Message 3 _____________________________________ Time: 12:57:15 PM PST US From: "Jim Ballenger" Subject: Re: Kolb-List: Smiling Weather Gods --> Kolb-List message posted by: "Jim Ballenger" Glad to see you got your first flight in yesterday. You are right the view is unobstructed. Mine stalls at 38 IAS. I ended up putting an aileron trim tab on the right to counter me in the left seat solo. Where did you end up putting your HZ stab leading edge in relations to the boom tube? Jim Ballenger MK III X 582 Virginia Beach, VA Do Not Archive ----- Original Message ----- From: Subject: Kolb-List: Smiling Weather Gods > --> Kolb-List message posted by: Cat36Fly@aol.com > > Today; Thanks to the weather gods watching over Delaware, Science and > understanding again overcame fear and superstition. Another Extra (615RT) > has taken > wing!!! > > She is a bit heavy on the left side, but stalls about 34 mph (clean), > climbs > quite briskly and boy what a view. Put .5 hrs on the bird. Now for some > fine > tuning. > > do not archive > > > ________________________________ Message 4 _____________________________________ Time: 04:37:55 PM PST US From: Cat36Fly@aol.com Subject: Re: Kolb-List: Smiling Weather Gods --> Kolb-List message posted by: Cat36Fly@aol.com Jim; Funny you should ask! My HS leading edge is just above the center of the boom tube as shown in the plans. I have the new brackets to change the location but wanted to see how it fly's prior to any changes. Today I adjusted the alienors a bit and am waiting for good weather again. Now that I know what to expect from the bird I will fly in less than ideal conditions (a little breeze, 3 miles, and 1000 ft +/-) I will probably need a trim tab also even though I put the battery to the right side. Once I get lateral stability (or close) I'll work on the pitch (a bit nose high right now). How was your original pitch attitude (first flight) and what corrections were needed? I used you prop setting numbers and set mine at 10 degrees. It seems good for now and saved me some time. THANKS! Larry Tasker 615RT Xtra/582/3 blade Warp (Taper Tip) ________________________________ Message 5 _____________________________________ Time: 05:00:30 PM PST US From: "Kolbdriver" Subject: Re: Kolb-List: EIS --> Kolb-List message posted by: "Kolbdriver" Paul, I talked with Sandy at Grand Rapids today and found out the EIS updates the screen 2 times per SECOND. Those are good folks at Grand Rapids, I have talked with them several times. I put them right up there with Travis, Dondi, and Jim. The beauty of the EIS is the alarm feature. After you set the alarm limits for min and max on all parameters the EIS will flash a red light if any thing gets out of limits. In the event of an alarm the screen changes to display that parameter. "Scanning the gauges" with an EIS consists of looking at the red light. Steven > --> Kolb-List message posted by: "Paul Petty" > > Thanks Steven, > This may be something worth looking into. > > Paul Petty > Building Ms. Dixie > Kolbra/912UL/Warp > > > do not archive > >