---------------------------------------------------------- Kolb-List Digest Archive --- Total Messages Posted Sun 12/17/06: 10 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 12:28 AM - Re: Propeller Information... (possums) 2. 06:42 AM - Multi-Engine Kolb?... (David Lehman) 3. 06:51 AM - Possum's Been At It Again?... (David Lehman) 4. 08:00 AM - q (russ kinne) 5. 01:22 PM - Re: Propeller Information... (John Hauck) 6. 01:26 PM - Re: Propeller Information... (John Hauck) 7. 04:04 PM - Re: Propeller Information... (Dana Hague) 8. 06:01 PM - Re: Propeller Information... (Richard Pike) 9. 06:30 PM - Re: Propeller Information... (John Hauck) 10. 08:04 PM - Re: Propeller Information... (David Lehman) ________________________________ Message 1 _____________________________________ Time: 12:28:40 AM PST US From: possums Subject: Re: Kolb-List: Propeller Information... At 07:34 PM 12/16/2006, you wrote: >I'm running a Tennessee 66x34 prop on my original Firestar with a >503DCDI... It's like flying around in first gear... I think that >the 66" is OK, but I must need more bite (pitch)... Anyone running >something similar that can give me some pitch advice?... > >Thanx... Yes.... Abandon all hope, yearnings who enter here. This is no place for a hobbit. ________________________________ Message 2 _____________________________________ Time: 06:42:39 AM PST US From: "David Lehman" Subject: Kolb-List: Multi-Engine Kolb?... OK, maybe not, but it looks like a Possums video... DVD http://vids.myspace.com/index.cfm?fuseaction=vids.individual&videoid=614598970 do not archive ________________________________ Message 3 _____________________________________ Time: 06:51:02 AM PST US From: "David Lehman" Subject: Kolb-List: Possum's Been At It Again?... OK, OK, I'll stop... http://vids.myspace.com/index.cfm?fuseaction=vids.individual&videoID=634125822 DVD do not archive ________________________________ Message 4 _____________________________________ Time: 08:00:42 AM PST US From: russ kinne Subject: Kolb-List: q In re recent talk about tie-down ropes -- this may be more academic than practical, but there have been recent MAJOR changes in cordage (ropes, strings, cables, whatever) that may interest the List. I just researched this subject for a boating magazine, and found that the new synthetics are nothing short of amazing. We all know nylon & dacron & polyester -- but the latter is very seriously weakened by UV; sunlight. Don=92t trust it. There are a lot of new fibers now, and some are FIFTEEN times stronger than steel. A half-inch rope will theoretically hold TEN TONS! (but don=92t stand under it) But they=92re all different. Some are stretchy (we don=92t want that) or very non-stretchy. Most are UV - sensitive and must be protected from sunlight by a woven cover of nylon or dacron. No big deal. The fibers named SPECTRA or DYNEEMA are reportedly the strongest fibers ever created. Others are brait, vectran, lycra, twaron, PEN, PBO, zylon, technora and others. All with different specs. The bottom line is that there are some VERY strong ropes available now. But of course there=92s a price. As I=92ve said, most of them are UV sensitive and should be protected. None of them like being knotted very much; use splices and fittings whenever possible. And of course they=92re expensive -- but you won=92t need a lot for your tie-down ropes. And an adequately=strong rope may be too thin to grab hold of and haul on. The best place to find them is in marine stores like West Products, or if by any chance you have access to a local sailmaker, pay them a visit and ask some questions. And bring your checkbook; something may be irrestible. Russ K ________________________________ Message 5 _____________________________________ Time: 01:22:09 PM PST US From: "John Hauck" Subject: Re: Kolb-List: Propeller Information... (pitch)... Anyone running something | similar that can give me some pitch advice?... | | Thanx... | | DVD DVD: Will your aircraft bump the redline, 6,500 rpm, WOT, straight and level flight? It should to get optimum climb and cruise performance. This is why a ground adjustable prop is so convenient. One can dial their prop right into the engine and aircraft, just like propping a boat. john h mkIII ________________________________ Message 6 _____________________________________ Time: 01:26:07 PM PST US From: "John Hauck" Subject: Re: Kolb-List: Propeller Information... Yep. Replace it with a 66" Ivo 2 blade. Richard Pike Richard: Excellent advice. However, if DVD does not pitch it correctly, might as well keep flying the Tennessee Prop. Bump the red line, WOT, straight and level fllight. john h mkIII ________________________________ Message 7 _____________________________________ Time: 04:04:50 PM PST US From: Dana Hague Subject: Re: Kolb-List: Propeller Information... All this talk of props... My Ultrastar has what I assume is the original 2-blade wood prop on the Cuyuna engine... since one of the chief complaints about the US is the prop ground clearance, would I be better off with a 3 blade prop of smaller diameter? -Dana -- -- Shaw's principle: Build a machine that a fool can use, and only a fool will want to use it. ________________________________ Message 8 _____________________________________ Time: 06:01:30 PM PST US From: "Richard Pike" Subject: Re: Kolb-List: Propeller Information... If the prop is presently likely to hit the ground, then you would be better off with anything that is smaller diameter. I am presently using an Ivo 2 blade 68" prop on my MKIII, but even when it had a 2 blade 64" Ivo, it still flew fine, just didn't accelerate or climb as well. Going to a bigger diameter prop really helps climb, diameter is not as important for cruise. If you can afford to give up a bit of climb, then the answer is probably yes. Richard Pike MKIII N420P (420ldPoops) dna ----- Original Message ----- From: "Dana Hague" Sent: Sunday, December 17, 2006 6:59 PM Subject: Re: Kolb-List: Propeller Information... > > All this talk of props... My Ultrastar has what I assume is the original > 2-blade wood prop on the Cuyuna engine... since one of the chief > complaints about the US is the prop ground clearance, would I be better > off with a 3 blade prop of smaller diameter? > > -Dana > -- > -- > Shaw's principle: > Build a machine that a fool can use, and only a fool will want to use it. > > > ________________________________ Message 9 _____________________________________ Time: 06:30:27 PM PST US From: "John Hauck" Subject: Re: Kolb-List: Propeller Information... be better | off with anything that is smaller diameter. | Richard Pike Richard/Dana/Gang: The Ultrastar was/is a unique little bird. Flies like a champion. Handles like a dream. Slow flight is its forte. Takes off and lands by its self, long as it is kept above the stall speed (on my 1984 model would fly at 25 mph indicated, stall a needle width below 25). Prop is not going to hit the ground. Not unless one breaks a main landing gear. Problem with prop/ground clearance is FOD. Unless one flies off a manicured grass strip or pavement, the prop will catch Hell. Jim Culver came up with a polyurethane leading edge that helped a great deal. However, taller grass, weeds, sand and rocks still took its toll on the blades. The perfect prop for the US was a Jim Culver 50X30. An US with a Cuyuna ULII02 would just bump the redline at WOT straight and level flight. That combo produced 85 mph. Not bad for a little UL. Personally, I do not think going to a smaller prop will help much when it comes to FOD and prop damage. Most likely will degrade performance of a great combo. john h mkIII ________________________________ Message 10 ____________________________________ Time: 08:04:15 PM PST US From: "David Lehman" Subject: Re: Kolb-List: Propeller Information... Thanx Richard and John... I don't know what my WOT RPM is straight and level, but with the Tennessee it's 6800 just after breaking ground with a nose up attitude, tells me that I'm way under-pitched... Before it fell off, I had a Warp Drive, but I think I'll replace the Tennessee woody with an IVO... Maybe Santa has a spare on the sleigh, naw, probably not... Thanx again... DVD do not archive On 12/17/06, John Hauck wrote: > > > > Yep. Replace it with a 66" Ivo 2 blade. > > Richard Pike > > > Richard: > > Excellent advice. > > However, if DVD does not pitch it correctly, might as well keep flying > the Tennessee Prop. > > Bump the red line, WOT, straight and level fllight. > > john h > mkIII > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message kolb-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Kolb-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/kolb-list Browse Digests http://www.matronics.com/digest/kolb-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.