Today's Message Index:
----------------------
1. 04:48 AM - props (tc1917)
2. 09:40 AM - Sport Pilot Article (Richard Girard)
3. 11:22 AM - Re: Sport Pilot Article (Jim ODay)
4. 01:19 PM - Latch for enclosure (Bill Vincent)
5. 01:50 PM - Re: Latch for enclosure (Larry Bourne)
6. 01:56 PM - Re: Latch for enclosure (Larry Bourne)
7. 02:33 PM - Re: Latch for enclosure (Richard Girard)
8. 02:33 PM - Re: Latch for enclosure (Dana Hague)
9. 02:46 PM - PMX visitors (william sullivan)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Just a heads up. I am selling two props from my 582 that were on my
SlingShot. One is the original IVO three blade ground adjust that I
installed new three years ago, 64" (Make Offer) and the other is a brand
new Warp 66" three blade with shinny new special hub. It doesnt even
have any bugs on it yet. Worked absolutely fantastic on the 582. This
is what a 582 likes. Will part with it for $750. I changed over to a
912 so I cannot use these props. Ted Cowan, Alabama, 334-480-0822.
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Sport Pilot Article |
The Kolb list's own Thom Riddle has an excellent article in the December
2007 "Sport Pilot" magazine on doing a proper engine preflight. Good job,
Thom and thanks. I got this issue almost a month late or I would have
commented earlier. That'll teach me to wait until the very last day before
renewing my EAA membership.
Rick
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Sport Pilot Article |
Wait till you see the January issue. Another well done piece by Thom.
do not archive
--------
Jim O'Day
Fargo, ND
Firestar II
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=156385#156385
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Latch for enclosure |
Hi Gang
I took the attached photo at my work place, it is on a FORTE metal band
saw; I think it is German built.
Does anyone know where I can purchase this spring toggle latch; this
latch will work in many different applications.
I looked at the FORTE parts list but they have only one size, 6 inches
long, which is too big, I also found spring toggles on the web but they
are not what I am looking for.
I am looking for smaller sizes than the 6 inches.
Thank you in advance,
Bill Vincent
FS II
Do Not Archive
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Latch for enclosure |
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Latch for enclosure |
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Latch for enclosure |
Bill, Try McMaster Carr (mcmaster.com) pages 2896-2900. They're listed as
draw latches or tension latches. I didn't see one exactly like the picture,
but many that perform in the same way.
Rick
On Jan 6, 2008 3:55 PM, Larry Bourne <biglar@gogittum.com> wrote:
>
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Latch for enclosure |
At 04:18 PM 1/6/2008, Bill Vincent wrote:
>Hi Gang
>I took the attached photo at my work place, it is on a FORTE metal band
>saw; I think it is German built.
>Does anyone know where I can purchase this spring toggle latch; this latch
>will work in many different applications...
Have you tried Southco? They sell many different types of latches.
-Dana
--
2000 mockingbirds = two kilomockingbirds
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
To those list members who inquired about traveling to PMX in Palmer, Mass., I
have been in touch with Ed Harvey, a member of the Silver Wings Ultralight Club
based at the now closed PMX airport. The club rents the old airport, and Ed
tells me they always welcome visitors. However, the airport only has people around
when a member happens to be present. The gate is locked when no one is there.
Ed is retired, and goes in there to mow the grass. The paved runway is said
to be unusable, and the club uses a 900' grass strip adjacent to the runway.
They say it is always open to touch and goes, etc., but if anything is needed
a club member should be there to arrange ground transport, gas, etc. Ed can
be reached by e-mail at the following address: edharvey1@juno.com
Thanks, guys, for the help and support. Hopefully we will have our Kold in
about three weeks.
Bill Sullivan
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|