Today's Message Index:
----------------------
1. 07:02 AM - Re: Kolb-List Digest: 5 Msgs - 06/24/10 (Bob Green)
2. 07:35 AM - Re: Re: Kolb-List Digest: 5 Msgs - 06/24/10 (John Hauck)
3. 09:01 AM - Re: Kolb-List Digest: 5 Msgs - 06/24/10 (George Bearden)
4. 07:42 PM - Full Moon (Eugene Zimmerman)
5. 07:50 PM - Re: Full Moon (John Hauck)
6. 08:41 PM - Re: Full Moon (chris davis)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RE: Kolb-List Digest: 5 Msgs - 06/24/10 |
Concerning the installation of the "H" bracket in the boom tube: I preferred not
to clamp or put bending pressure on the outside of boom tube... What I did
was put the "H" bracket in place and using either 1" or 2" think boards I placed
one on the top leg of the "H" bracket and the other on the opposite leg.
I then pushed a wedge shaped 2x4 between the two flat boards causing the two
bracket legs to flex to a tight fit against the inner walls of the tube. Not
much pressure was required and this insured a snug fit between the two ("H" bracket
and boom tube) for riveting purposes.
As Richard Pike says... "For what it is worth"...
Bob
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RE: Kolb-List Digest: 5 Msgs - 06/24/10 |
> Concerning the installation of the "H" bracket in the boom tube: I
> preferred not to clamp or put bending pressure on the outside of boom
> tube... > Bob
Cabinet maker's/carpenter's wooden clamps work well. Only slight pressure
is required to get the job done.
john h
mkIII
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RE: Kolb-List Digest: 5 Msgs - 06/24/10 |
>The best way to exactly match rivet holes and reuse the H-section is to
make a paper tube template.
I shouldn't even pipe up as I am not a pilot and don't have a Kolb. However,
fine points of etiquette have always escaped me so...
I have JUST retired after a long and glorious career in GIS. Think automated
mapping, spatial analysis, aerial photos, GPS, HUGE plotters and scanners.
We quit using paper for critical drawings years ago as it is not
dimensionally stable. Paper stretches, humidity affects it, John down the
hall leaves it lying around with coffee stains...
Maybe use mylar, eh?
GeoB
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
My wife took this picture of me on final approach Friday evening.
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
From: "Eugene Zimmerman" <etzimm@gmail.com>
> My wife took this picture of me on final approach Friday evening.
Nice, unusual photo.
john h
mkIII
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Nice Pic ! Makesme jealous. C.
Chris Davis
KXP 503 492 hrs
Glider Pilot
Disabled from crash building Firefly
----- Original Message ----
From: Eugene Zimmerman <etzimm@gmail.com>
Sent: Fri, June 25, 2010 10:41:12 PM
Subject: Kolb-List: Full Moon
My wife took this picture of me on final approach Friday evening.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|