---------------------------------------------------------- Kolb-List Digest Archive --- Total Messages Posted Sat 04/02/11: 9 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 01:06 PM - Re: Video of Tornado at Sun n Fun (Rick Lewis) 2. 03:22 PM - Tiny tach?? (Larry Cottrell) 3. 04:53 PM - survey (Dana Hague) 4. 05:50 PM - Re: survey (b d) 5. 05:53 PM - Re: Tiny tach?? (George Alexander) 6. 06:34 PM - Re: Re: Tiny tach?? (Larry Cottrell) 7. 06:38 PM - Re: survey (Dana Hague) 8. 06:38 PM - Re: survey (Dana Hague) 9. 07:08 PM - Re: Re: Tiny tach?? (Dana Hague) ________________________________ Message 1 _____________________________________ Time: 01:06:13 PM PST US Subject: Kolb-List: Re: Video of Tornado at Sun n Fun From: "Rick Lewis" It looks to me like the claw tie down would be great in dirt but do little in sand. Really doubt that much of anything would do well in sand unless it's corked screwed down really deep. -------- Rick Lewis (VW Watercooled Engine) Read this topic online here: http://forums.matronics.com/viewtopic.php?p=335863#335863 ________________________________ Message 2 _____________________________________ Time: 03:22:12 PM PST US From: "Larry Cottrell" Subject: Kolb-List: Tiny tach?? Gang, I need a bit of help with RPM monitoring. My EIS has intermittent loss of signal, probably due to a intermittent ground. Every thing else works on the EIS, and while not a serious problem, It is irritating enough that I would like to either fix it or have a back up. I thought first of a Tiny Tach. Aircraft Spruce only lists 3 different models, a 2 stroke that might work with my HKS, a diesel model, and a really "fancy" one that cost twice as much as the two stroke one. I don't have a problem with any of them, I just don't want to have to send one back because its not working with my engine. I also need a longer lead wire than 6 feet. Any help and advice would be appreciated. Larry Note: If you forward this email, please delete the forwarding history, which includes my email address. ________________________________ Message 3 _____________________________________ Time: 04:53:06 PM PST US From: Dana Hague Subject: Kolb-List: survey From the Homebuiltairplanes.com forum: >Builder/Pilot/Grad student - request help for final project > > My name is Kory Klismith. I've been reading these forums for a few > years. My wife and I are building a Murphy Elite. I am currently working > to finish my master's degree through Embry-Riddle Aeronautical > University. To complete my degree I need to complete a research project. > As part of this project, I have devised an online questionnaire using > surveymonkey.com. > My project focuses on safety and reliability of piston and rotary > engines used in experimental aircraft. The survey is open to anybody who > currently owns/flys an experimental aircraft or has a project under > construction. > > If you can spare a few minutes, I request your assistance in > completing the short questionnaire at the following address: > https://www.surveymonkey.com/s/ExpAc..._Questionnaire > > If you know of anybody else who's not a regular to this forum that > builds/operates experimental aircraft, requesting your assistance in > forwarding this link to them. No personnally identifiable information > will be collected. This is strictly for educational purposes. > > If you have any questions or concerns, please feel free to contact me > via email: koryklismith@hotmail.com > > Thank you very much for your time! > Respectfully, > Kory "Flex" Klismith > ERAU Grad Student > Murphy Elite #678 under construction Do not archive -Dana -- In England, the cops say, 'Halt or I'll say halt again!' ________________________________ Message 4 _____________________________________ Time: 05:50:31 PM PST US Subject: Re: Kolb-List: survey From: b d Using your link, I am unable to get to your survey . . . help plz On Sat, Apr 2, 2011 at 4:40 PM, Dana Hague wrote: > > From the Homebuiltairplanes.com forum: > > Builder/Pilot/Grad student - request help for final project >> >> My name is Kory Klismith. I've been reading these forums for a few >> years. My wife and I are building a Murphy Elite. I am currently working to >> finish my master's degree through Embry-Riddle Aeronautical University. To >> complete my degree I need to complete a research project. As part of this >> project, I have devised an online questionnaire using surveymonkey.com. >> My project focuses on safety and reliability of piston and rotary >> engines used in experimental aircraft. The survey is open to anybody who >> currently owns/flys an experimental aircraft or has a project under >> construction. >> >> If you can spare a few minutes, I request your assistance in completing >> the short questionnaire at the following address: >> https://www.surveymonkey.com/s/ExpAc..._Questionnaire >> >> If you know of anybody else who's not a regular to this forum that >> builds/operates experimental aircraft, requesting your assistance in >> forwarding this link to them. No personnally identifiable information will >> be collected. This is strictly for educational purposes. >> >> If you have any questions or concerns, please feel free to contact me >> via email: koryklismith@hotmail.com >> >> Thank you very much for your time! >> Respectfully, >> Kory "Flex" Klismith >> ERAU Grad Student >> Murphy Elite #678 under construction >> > > Do not archive > > -Dana > -- > In England, the cops say, 'Halt or I'll say halt again!' > > ________________________________ Message 5 _____________________________________ Time: 05:53:55 PM PST US Subject: Kolb-List: Re: Tiny tach?? From: "George Alexander" lcottrell wrote: > Gang, I need a bit of help with RPM monitoring. My EIS has intermittent loss of signal, probably due to a intermittent ground. Every thing else works on the EIS, and while not a serious problem, It is irritating enough that I would like to either fix it or have a back up. I thought first of a Tiny Tach. Aircraft Spruce only lists 3 different models, a 2 stroke that might work with my HKS, a diesel model, and a really "fancy" one that cost twice as much as the two stroke one. I don't have a problem with any of them, I just don't want to have to send one back because its not working with my engine. I also need a longer lead wire than 6 feet. Any help and advice would be appreciated. > > Larry > > Note: If you forward this email, please delete the forwarding history, which includes my email address. > Larry: You might consider going directly to Tiny-Tach. They would be able to sell you the model you need for your engine, and they can add (at a charge) the additional length that you would need. http://tinytach.com/tinytach/index.php -------- George Alexander FS II R503 N709FS http://www.oh2fly.net Read this topic online here: http://forums.matronics.com/viewtopic.php?p=335889#335889 ________________________________ Message 6 _____________________________________ Time: 06:34:25 PM PST US From: "Larry Cottrell" Subject: Re: Kolb-List: Re: Tiny tach?? Thanks, I will try that first thing Monday. Larry Note: If you forward this email, please delete the forwarding history, which includes my email address. Larry: You might consider going directly to Tiny-Tach. They would be able to sell you the model you need for your engine, and they can add (at a charge) the additional length that you would need. http://tinytach.com/tinytach/index.php -------- George Alexander FS II R503 N709FS http://www.oh2fly.net Read this topic online here: http://forums.matronics.com/viewtopic.php?p=335889#335889 ________________________________ Message 7 _____________________________________ Time: 06:38:23 PM PST US From: Dana Hague Subject: Re: Kolb-List: survey Sorry, apparently the link didn't go through, it is: -Dana At 07:40 PM 4/2/2011, Dana Hague wrote: > > From the Homebuiltairplanes.com forum: > >>Builder/Pilot/Grad student - request help for final project >> >> My name is Kory Klismith. I've been reading these forums for a few >> years. My wife and I are building a Murphy Elite. I am currently working >> to finish my master's degree through Embry-Riddle Aeronautical >> University. To complete my degree I need to complete a research project. >> As part of this project, I have devised an online questionnaire using >> surveymonkey.com. >> My project focuses on safety and reliability of piston and rotary >> engines used in experimental aircraft. The survey is open to anybody who >> currently owns/flys an experimental aircraft or has a project under >> construction. >> >> If you can spare a few minutes, I request your assistance in >> completing the short questionnaire at the following address: >> https://www.surveymonkey.com/s/ExpAc..._Questionnaire >> >> If you know of anybody else who's not a regular to this forum that >> builds/operates experimental aircraft, requesting your assistance in >> forwarding this link to them. No personnally identifiable information >> will be collected. This is strictly for educational purposes. >> >> If you have any questions or concerns, please feel free to contact >> me via email: koryklismith@hotmail.com >> >> Thank you very much for your time! >> Respectfully, >> Kory "Flex" Klismith >> ERAU Grad Student >> Murphy Elite #678 under construction > >Do not archive > >-Dana >-- >In England, the cops say, 'Halt or I'll say halt again!' > > -- A common mistake that people make when trying to design something completely foolproof is to underestimate the ingenuity of complete fools. ________________________________ Message 8 _____________________________________ Time: 06:38:23 PM PST US From: Dana Hague Subject: Re: Kolb-List: survey Sorry, apparently the link didn't go through, it is: -Dana At 07:40 PM 4/2/2011, Dana Hague wrote: > > From the Homebuiltairplanes.com forum: > >>Builder/Pilot/Grad student - request help for final project >> >> My name is Kory Klismith. I've been reading these forums for a few >> years. My wife and I are building a Murphy Elite. I am currently working >> to finish my master's degree through Embry-Riddle Aeronautical >> University. To complete my degree I need to complete a research project. >> As part of this project, I have devised an online questionnaire using >> surveymonkey.com. >> My project focuses on safety and reliability of piston and rotary >> engines used in experimental aircraft. The survey is open to anybody who >> currently owns/flys an experimental aircraft or has a project under >> construction. >> >> If you can spare a few minutes, I request your assistance in >> completing the short questionnaire at the following address: >> https://www.surveymonkey.com/s/ExpAc..._Questionnaire >> >> If you know of anybody else who's not a regular to this forum that >> builds/operates experimental aircraft, requesting your assistance in >> forwarding this link to them. No personnally identifiable information >> will be collected. This is strictly for educational purposes. >> >> If you have any questions or concerns, please feel free to contact >> me via email: koryklismith@hotmail.com >> >> Thank you very much for your time! >> Respectfully, >> Kory "Flex" Klismith >> ERAU Grad Student >> Murphy Elite #678 under construction > >Do not archive > >-Dana >-- >In England, the cops say, 'Halt or I'll say halt again!' > > -- A common mistake that people make when trying to design something completely foolproof is to underestimate the ingenuity of complete fools. ________________________________ Message 9 _____________________________________ Time: 07:08:45 PM PST US From: Dana Hague Subject: Re: Kolb-List: Re: Tiny tach?? At 08:51 PM 4/2/2011, George Alexander wrote: > > >Larry: >You might consider going directly to Tiny-Tach. They would be able to >sell you the model you need for your engine, and they can add (at a >charge) the additional length that you would need. > >http://tinytach.com/tinytach/index.php You might also look into the ENM tachs. They're similar to the Tiny Tach, but are programmable so you set it to work with your engine rather than having to buy a particular model that matches. I have also found them to be more reliable than the Tiiny Tachs. -Dana -- But if we LEGALIZE it, we can't take your HOUSE! ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message kolb-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Kolb-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/kolb-list Browse Digests http://www.matronics.com/digest/kolb-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.