Today's Message Index:
----------------------
1. 07:25 AM - Cooling and warming our Rotax engines:-) (herb)
2. 10:36 AM - Re: q (planecrazzzy)
3. 11:00 AM - Re: For Kolb Private Strip owners (planecrazzzy)
4. 05:42 PM - Re: Re: For Kolb Private Strip owners (Richard Girard)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Cooling and warming our Rotax engines:-) |
I was always amazed that the 277 used almost fuel as my 447... On a
Kitten, then 277 had to run very hard most of the time..while my 447
could cruise the Firefly very nicely between 5200 and 5600...
I was thinking about the twins...I have seen the 277 on a kitten and it
definitely had quite a bit of vibration... Maybe some sort of sliding
device with an automatic spring loaded return to full open.. Mainly on
the radiator since I now have a 582... with single radiator.. Could be
that something on the order of a window shade would work..With
different material of course.. Herb
On 02/18/2013 11:13 PM, wakataka wrote:
>
> After two cold seizures, I tried to build something like that for my free air
277, but the vibration from that little beast kept tearing apart whatever design
I came up with. I finally solved the problem by having the cylinder honed
out about 0.003 larger than factory spec and running a main jet 2 steps richer
than spec. I'm also very careful not to go to full throttle immediately after
a long descent at idle. On a touch and go, I'll usually take off with about
3/4 throttle and wait until the CHT gets up to 250 before going to full throttle.
>
> --------
> There is something fascinating about science. One gets such wholesale returns
of conjecture out of such a trifling investment of fact.
>
> Mark Twain
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
.
HA !!!!,
Step away from the Forum Russ...
.
You only THINK your addicted...
.
Gotta Fly...
Mike & "Jaz" the Flying Dogz
.
Building a Wittman "Buttercup - "Miss Tickle Madness"
.
.
--------
.
.
.
.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=394598#394598
Attachments:
http://forums.matronics.com//files/bc_controls_check_and_shake_down_8_148.jpg
http://forums.matronics.com//files/18_baraboo_07_330.jpg
http://forums.matronics.com//files/20_baraboo_07_126.jpg
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: For Kolb Private Strip owners |
Hi Dennis,
Nice strip...
I wish I had some of that Equip to carve out my Airstrip...
I bought a 580 Case Backhoe/loader... I'm currently removing trees...
I've established the length... I need to make it WIDER.
Then I need to shift some dirt around...
.
Gotta Fly...
Mike & "Jaz" retiring Up North to the cabins ( Soon )
.
PS The Cabins are just to the left of the runway in the picture...
--------
.
.
.
.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=394602#394602
Attachments:
http://forums.matronics.com//files/new_rear_tires_1_200.jpg
http://forums.matronics.com//files/untitled_919.jpg
http://forums.matronics.com//files/runway_6_201.jpg
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: For Kolb Private Strip owners |
Mike, Sounds great, have you started planning for the party?
Attached is the Minnesota RULA which exempts non-commercial aircraft flying
from being a liability for the land owner.
Rick Girard
do not archive
On Tue, Feb 19, 2013 at 1:00 PM, planecrazzzy <planecrazzzy@yahoo.com>wrote:
>
> Hi Dennis,
> Nice strip...
>
> I wish I had some of that Equip to carve out my Airstrip...
>
> I bought a 580 Case Backhoe/loader... I'm currently removing trees...
>
> I've established the length... I need to make it WIDER.
>
> Then I need to shift some dirt around...
> .
> Gotta Fly...
> Mike & "Jaz" retiring Up North to the cabins ( Soon )
> .
> PS The Cabins are just to the left of the runway in the picture...
>
> --------
> .
> .
> .
> .
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=394602#394602
>
>
> Attachments:
>
> http://forums.matronics.com//files/new_rear_tires_1_200.jpg
> http://forums.matronics.com//files/untitled_919.jpg
> http://forums.matronics.com//files/runway_6_201.jpg
>
>
--
Zulu Delta
Mk IIIC
Thanks, Homer GBYM
It isn't necessary to have relatives in Kansas City in order to be unhappy.
- Groucho Marx
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|