Today's Message Index:
----------------------
1. 10:36 AM - mounting hinges (Nick Cassara)
2. 11:51 AM - Re: mounting hinges (Ralph B)
3. 12:23 PM - Re: mounting hinges (b young)
4. 07:01 PM - Re: Kolb location at S&F (Rick Lewis)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hello Kolbers,
I have built my wings, horizontal stabilizers, and vertical stabilizer. Now
I need to mount my hinges.I remember someone split each hinges into thirds
and mounted the hinge on both sides of the center line, on the trailing edge
tube, rather than having the hinge mounted all on one side. This seems like
a good idea to me, but I cannot find the "posts" in the Archives. I would be
grateful if anyone has thoughts on the pro's or con's of this approach.
Thanks,
Nick Cassara
Palmer, Alaska
N607AK Kolbra #1
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: mounting hinges |
"nickc(at)mtaonline.net"
> Hello Kolbers,
>
> I have built my wings, horizontal stabilizers, and vertical stabilizer. Now I
need to mount my hingesI remember someone split each hinges into thirds and mounted
the hinge on both sides of the center line, on the trailing edge tube,
rather than having the hinge mounted all on one side. This seems like a good idea
to me, but I cannot find the posts in the Archives. I would be grateful if
anyone has thoughts on the pros or cons of this approach.
>
> Thanks,
>
> Nick Cassara
> Palmer, Alaska
>
> N607AK Kolbra #1
Nick, my Kolbra was built according to plan and the hinges were not split.
Ralph
--------
Ralph B
Original Firestar 447
N91493 E-AB
1000+ hours
26 years flying it
Kolbra 912ULS
N20386
200 hours
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=398258#398258
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: mounting hinges |
I went into the search engine and did a search on =9Cx
hinges=9D found this
http://www.mindspring.com/~possums/Xhingestrailingedge.jpg and
http://www.mindspring.com/~possums/HINGESML.jpg if you do the
search, you may find more. as I remember, you have to cut out every
other spot on each hinges that the wire hinge pin goes through. I have
no experience to determine if it is a good idea or not. hope this is
what you are looking for.
boyd young
From: Nick Cassara
Sent: Tuesday, April 09, 2013 11:36 AM
Subject: Kolb-List: mounting hinges
Hello Kolbers,
I have built my wings, horizontal stabilizers, and vertical stabilizer.
Now I need to mount my hingesI remember someone split each
hinges into thirds and mounted the hinge on both sides of the center
line, on the trailing edge tube, rather than having the hinge mounted
all on one side. This seems like a good idea to me, but I cannot find
the =9Cposts=9D in the Archives. I would be grateful if
anyone has thoughts on the pro=99s or con=99s of this
approach.
Thanks,
Nick Cassara
Palmer, Alaska
N607AK Kolbra #1
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Kolb location at S&F |
I'm here at sun-n-fun and Kolb is not here anywhere I look. Hope they didn't have
trouble getting here, will look again tomorrow...
Rick
--------
Rick Lewis
(VW Watercooled Engine)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=398301#398301
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|