Today's Message Index:
----------------------
0. 12:12 AM - Coming Soon - The List of Contributors - Please Make A Contribution Today! (Matt Dralle)
1. 10:09 AM - Re: tail wheel turning right (Arizona Flyer)
2. 08:12 PM - Re: Re: tail wheel turning right (Gary Aman)
Message 0
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Coming Soon - The List of Contributors - Please Make A Contribution |
Today!
Each year at the end of the List Fund Raiser, I post a message acknowledging everyone
that so generously made a Contribution to support the Lists. Its my way
of publicly thanking everyone that took a minute to show their appreciation
for the Lists.
Please take a moment and assure that your name is on that List of Contributors
(LOC)! As a number of members have pointed out over the years, the List seems
at least as valuable a building / entertainment tool as your typical magazine
subscription!
Assure that your name is on this year's LOC! Show others that you appreciate the
Lists. Making a Contribution to support the Lists is fast and easy using your
Credit card or Paypal on the Secure Web Site:
http://www.matronics.com/contribution
or by dropping a personal check in the mail to:
Matt Dralle / Matronics
581 Jeannie Way
Livermore CA 94550
I would like to thank everyone that has so generously made a Contribution thus
far in this year's List Fund Raiser! Remember that its YOUR support that keeps
these Lists going and improving! Don't forget to include a little comment about
how the Lists have helped you!
Best regards,
Matt Dralle
Matronics Email List Administrator
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: tail wheel turning right |
byoungplumbing(at)gmail.c wrote:
> is this the tail wheel you are having trouble turning right?
>
> [img]cid:9D2DD9D74D6F4CCD928710FFF260BAEF@BYoungHP[/img]
>
> and did you mention the wheel turns easy till the actuating bar is bolted on
the top?
>
> if all above is true,,,,, there may be a missing washer under the actuating
bar,,,,, or the housing may be a bit too tall.
>
> this is the wheel I am using now and wish I had changed from the pizza cutter
wheel much sooner. I love it. and even more so since I put in better bearings.
>
> boyd young
I like that. Do you know the inside diameter? I'd like to see if that will fit
onto the male shaft coming from my rear boom. What does that one cost? Travis
at Kolb told me the new tail wheel with 1" wide wheel is $300+ dollars but he
said it's a whole new one that needs to be put on the boom. The one in your picture
looks like it might slide right on my shaft. Thanks for the picture, I can
finally see one!
--------
"Life should be lived as a bold adventure, I refuse to tiptoe through life
just to arrive safely at death"
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=412418#412418
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: tail wheel turning right |
If the wheel is not exactly vertical ,or leaning when stationary,it will gi
ve you a fit.The tail spring must be tight in the support tube and the rest
of the assy tight on the spring rod.If it can move off of dead vertical it
will be easy to steer on way and almost impossible the other.The rods get
sloppy in the tube and the bolt hole elongates letting the rod twist.I cure
d that issue on my Mk3 by clamping the rod in the tube
G.Aman
-----Original Message-----
From: Arizona Flyer <heracesthesun@yahoo.com>
Sent: Thu, Nov 7, 2013 1:09 pm
Subject: Kolb-List: Re: tail wheel turning right
byoungplumbing(at)gmail.c wrote:
> is this the tail wheel you are having trouble turning right?
>
> [img]cid:9D2DD9D74D6F4CCD928710FFF260BAEF@BYoungHP[/img]
>
> and did you mention the wheel turns easy till the actuating bar is bolte
d on
the top?
>
> if all above is true,,,,, there may be a missing washer under the actu
ating
bar,,,,, or the housing may be a bit too tall.
>
> this is the wheel I am using now and wish I had changed from the pizza
cutter wheel much sooner. I love it. and even more so since I put in b
etter
bearings.
>
> boyd young
I like that. Do you know the inside diameter? I'd like to see if that will
fit
onto the male shaft coming from my rear boom. What does that one cost? Trav
is at
Kolb told me the new tail wheel with 1" wide wheel is $300+ dollars but he
said
it's a whole new one that needs to be put on the boom. The one in your pict
ure
looks like it might slide right on my shaft. Thanks for the picture, I can
finally see one!
--------
"Life should be lived as a bold adventure, I refuse to tiptoe through
life
just to arrive safely at death"
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=412418#412418
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|