Today's Message Index:
----------------------
1. 12:50 AM - Re: Xtra Control Problems (JC Gilpin)
2. 04:43 AM - Re: Re: Xtra Control Problems (Dennis Rowe)
3. 04:25 PM - new video (Larry Cottrell)
4. 07:05 PM - Re: new video (Brad Nation)
5. 10:18 PM - Re: Xtra Control Problems (Richard Girard)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Xtra Control Problems |
By chance, did those trim tabs get bent to that ridiculous angle during
trailering??
Bend them straight with the control surface and see what it feels like,
then start adjusting from there.....
JG
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Xtra Control Problems |
Bingo John, but I'd bend them back to 15 to 30 degrees instead of going all t
he way straight, probably be in the ball park.
Dennis "Skid" Rowe
Mk3, 690L-70, Leechburg, PA
> On May 24, 2014, at 3:50 AM, JC Gilpin <j.gilpin@bigpond.com> wrote:
>
> By chance, did those trim tabs get bent to that ridiculous angle during tr
ailering??
>
> Bend them straight with the control surface and see what it feels like, th
en start adjusting from there.....
>
> JG
>
>
==========================
=========
==========================
=========
==========================
=========
==========================
=========
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
https://vimeo.com/96347947
password: owyheeflyer
My niece is visiting and is crazy about Kolbs. John normally flies her when
he is here, but since he is coming cross country in his truck its up to me
to give her a flight.
Larry
--
*If you forward this email, or any part of it, please remove my email
address before sending.*
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Another nice video. Thanks for sharing. Your part of Oregon sure look
like New Mexico and according to my parents and aunt, who are from
Pendleton, it is
You said at the end that =93it looks like she heated=94. It sure looks
like to me like quite the opposite.
Brad
___________________________
=93Freedom is never more than one generation away from extinction. We
didn't pass it to our children in the bloodstream. It must be fought
for, protected, and handed on for them to do the same, or one day we
will spend our sunset years telling our children and our children's
children what it was once like in the United States where men were
free.=94
-- President Ronald Reagan
On May 24, 2014, at 17:24 , Larry Cottrell <lcottrell1020@gmail.com>
wrote:
> https://vimeo.com/96347947
>
> password: owyheeflyer
>
> My niece is visiting and is crazy about Kolbs. John normally flies her
when he is here, but since he is coming cross country in his truck its
up to me to give her a flight.
> Larry
>
> --
> If you forward this email, or any part of it, please remove my email
address before sending.
>
>
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Xtra Control Problems |
Brad, I posted the Kolb drawing for the recommended trim tabs recently.
I've attached it to this post, too.
What tail wheel do you have?
Rick Girard
do not archive
On Fri, May 23, 2014 at 9:51 PM, Brad Nation <nationcap@comcast.net> wrote:
> That seems to be the consensus of everyone who looks at the tabs, more
> drag than anything else. As for the toe in/out, no, not yet. Suggestion
s?
>
> Brad
>
> On May 22, 2014, at 21:43 , B Young <byoungplumbing@gmail.com> wrote:
>
> Trim tabs at 90 deg.... I don't understand,, tab deflected that far
> should stall and not work as needed.. or intended.. what is your toe i
n
> / out measurements? Duo you know how to get accurate measurements?
>
> Boyd
>
> *
>
> href="http://www.matronics.com/Navigator?Kolb-List <http://www.matronic
s.com/Navigator?Kolb-List>">http://www.matronics.com/Navigator?Kolb-List <h
ttp://www.matronics.com/Navigator?Kolb-List>
> href="http://forums.matronics.com/ <http://forums.matronics.com/>">http
://forums.matronics.com <http://forums.matronics.com>
> href="http://www.matronics.com/contribution <http://www.matronics.com/c
ontribution>">http://www.matronics.com/contribution <http://www.matronics.c
om/contribution>
>
> *
>
>
> *Brad*
> *___________________________*
> *=9CFreedom is never more than one generation away from extinction.
We
> didn't pass it to our children in the bloodstream. It must be fought for,
> protected, and handed on for them to do the same, or one day we will spen
d
> our sunset years telling our children and our children's children what it
> was once like in the United States where men were free.=9D*
>
> *-- President Ronald Reagan*
>
>
> *
>
===========
onics.com/Navigator?Kolb-List>
===========
===========
om/contribution>
===========
>
> *
>
>
--
Zulu Delta
Mk IIIC
Thanks, Homer GBYM
It isn't necessary to have relatives in Kansas City in order to be unhappy.
- Groucho Marx
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|