---------------------------------------------------------- Kolb-List Digest Archive --- Total Messages Posted Sat 05/24/14: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 12:50 AM - Re: Xtra Control Problems (JC Gilpin) 2. 04:43 AM - Re: Re: Xtra Control Problems (Dennis Rowe) 3. 04:25 PM - new video (Larry Cottrell) 4. 07:05 PM - Re: new video (Brad Nation) 5. 10:18 PM - Re: Xtra Control Problems (Richard Girard) ________________________________ Message 1 _____________________________________ Time: 12:50:55 AM PST US Subject: Kolb-List: Re: Xtra Control Problems From: JC Gilpin By chance, did those trim tabs get bent to that ridiculous angle during trailering?? Bend them straight with the control surface and see what it feels like, then start adjusting from there..... JG ________________________________ Message 2 _____________________________________ Time: 04:43:02 AM PST US From: Dennis Rowe Subject: Re: Kolb-List: Re: Xtra Control Problems Bingo John, but I'd bend them back to 15 to 30 degrees instead of going all t he way straight, probably be in the ball park. Dennis "Skid" Rowe Mk3, 690L-70, Leechburg, PA > On May 24, 2014, at 3:50 AM, JC Gilpin wrote: > > By chance, did those trim tabs get bent to that ridiculous angle during tr ailering?? > > Bend them straight with the control surface and see what it feels like, th en start adjusting from there..... > > JG > > ========================== ========= ========================== ========= ========================== ========= ========================== ========= > ________________________________ Message 3 _____________________________________ Time: 04:25:13 PM PST US Subject: Kolb-List: new video From: Larry Cottrell https://vimeo.com/96347947 password: owyheeflyer My niece is visiting and is crazy about Kolbs. John normally flies her when he is here, but since he is coming cross country in his truck its up to me to give her a flight. Larry -- *If you forward this email, or any part of it, please remove my email address before sending.* ________________________________ Message 4 _____________________________________ Time: 07:05:08 PM PST US From: Brad Nation Subject: Re: Kolb-List: new video Another nice video. Thanks for sharing. Your part of Oregon sure look like New Mexico and according to my parents and aunt, who are from Pendleton, it is You said at the end that =93it looks like she heated=94. It sure looks like to me like quite the opposite. Brad ___________________________ =93Freedom is never more than one generation away from extinction. We didn't pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same, or one day we will spend our sunset years telling our children and our children's children what it was once like in the United States where men were free.=94 -- President Ronald Reagan On May 24, 2014, at 17:24 , Larry Cottrell wrote: > https://vimeo.com/96347947 > > password: owyheeflyer > > My niece is visiting and is crazy about Kolbs. John normally flies her when he is here, but since he is coming cross country in his truck its up to me to give her a flight. > Larry > > -- > If you forward this email, or any part of it, please remove my email address before sending. > > > ________________________________ Message 5 _____________________________________ Time: 10:18:10 PM PST US Subject: Re: Kolb-List: Xtra Control Problems From: Richard Girard Brad, I posted the Kolb drawing for the recommended trim tabs recently. I've attached it to this post, too. What tail wheel do you have? Rick Girard do not archive On Fri, May 23, 2014 at 9:51 PM, Brad Nation wrote: > That seems to be the consensus of everyone who looks at the tabs, more > drag than anything else. As for the toe in/out, no, not yet. Suggestion s? > > Brad > > On May 22, 2014, at 21:43 , B Young wrote: > > Trim tabs at 90 deg.... I don't understand,, tab deflected that far > should stall and not work as needed.. or intended.. what is your toe i n > / out measurements? Duo you know how to get accurate measurements? > > Boyd > > * > > href="http://www.matronics.com/Navigator?Kolb-List ">http://www.matronics.com/Navigator?Kolb-List > href="http://forums.matronics.com/ ">http ://forums.matronics.com > href="http://www.matronics.com/contribution ">http://www.matronics.com/contribution > > * > > > *Brad* > *___________________________* > *=9CFreedom is never more than one generation away from extinction. We > didn't pass it to our children in the bloodstream. It must be fought for, > protected, and handed on for them to do the same, or one day we will spen d > our sunset years telling our children and our children's children what it > was once like in the United States where men were free.=9D* > > *-- President Ronald Reagan* > > > * > =========== onics.com/Navigator?Kolb-List> =========== =========== om/contribution> =========== > > * > > -- Zulu Delta Mk IIIC Thanks, Homer GBYM It isn't necessary to have relatives in Kansas City in order to be unhappy. - Groucho Marx ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message kolb-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Kolb-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/kolb-list Browse Digests http://www.matronics.com/digest/kolb-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.