Kolb-List Digest Archive

Sat 04/03/21


Total Messages Posted: 4



Today's Message Index:
----------------------
 
     1. 07:17 AM - Clutch for warp drive prop (Dan Ried)
     2. 09:19 AM - Re: Clutch for warp drive prop (william sullivan)
     3. 09:30 AM - Re: Clutch for warp drive prop (Roy Spangler)
     4. 05:50 PM - Thrust line...? (Nick Cassara)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 07:17:40 AM PST US
    From: Dan Ried <mibear117@gmail.com>
    Subject: Clutch for warp drive prop
    I will try a photo again. Thanks Dana, Bear Lake, Mi.


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:19:10 AM PST US
    From: william sullivan <williamtsullivan@att.net>
    Subject: Re: Clutch for warp drive prop
    All photos came through. I can't help, but perhaps Richard Pike or John Ha uck can. You might also try cross-posting to the Rotax List. Good luck Bill Sullivan On Saturday, April 3, 2021, 10:17:49 AM EDT, Dan Ried <mibear117@gmail .com> wrote: I will try a photo again. =C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2- Thanks Dana, Bear Lake, Mi.


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:30:36 AM PST US
    From: Roy Spangler <roy.spangler@kirtland.edu>
    Subject: Re: Clutch for warp drive prop
    I would check with Steve Henry - he has been using clutches for quite some time. roy On Sat, Apr 3, 2021 at 12:21 PM william sullivan <williamtsullivan@att.net> wrote: > All photos came through. I can't help, but perhaps Richard Pike or John > Hauck can. You might also try cross-posting to the Rotax List. > > Good luck > > Bill Sullivan > > > On Saturday, April 3, 2021, 10:17:49 AM EDT, Dan Ried <mibear117@gmail.com> > wrote: > > > I will try a photo again. > > Thanks Dana, Bear Lake, Mi. > >


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 05:50:13 PM PST US
    From: Nick Cassara <nickc@mtaonline.net>
    Subject: Thrust line...?
    Kolbers, I have been interest in the talk about desired thrust line. I took a piece line and attached to the front of my engine mount plate, I then walked it back to the tail, and lowered the string until it was making contact with the whole upper surface of the mount plate. The string ends up 4 inches above the end of the boom tube. The center of the prop is 8 inches above the string linei.e.12 above the top of the boom tube end. My Kolbra is the prototype, of the Kolbras. Nick Cassara Palmer, Alaska




    Other Matronics Email List Services

  • Post A New Message
  •   kolb-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Kolb-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/kolb-list
  • Browse Kolb-List Digests
  •   http://www.matronics.com/digest/kolb-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --