Today's Message Index:
----------------------
1. 10:15 AM - Newly built Slingshot rudder =?ISO-8859-1?Q?question? (Charlie Mike)
2. 10:22 AM - =?UTF-8?Q?Re=3a_Kolb-List=3a_Newly_built_Slingshot_rudder_question?= =?UTF-8?B?w6LigqzCpg==? (Charlie England)
3. 10:23 AM - =?UTF-8?Q?Re:__Newly_built_?= =?UTF-8?Q?Slingshot_rudder_question=C3=A2=82=AC=C2? (william sullivan)
4. 08:16 PM - Re: Newly built Slingshot rudder =?ISO-8859-1?Q?question=C3=A2=82=AC=C2? (Charlie Mike)
5. 08:24 PM - Re: Newly built Slingshot rudder =?ISO-8859-1?Q?question=C3=A2=82=AC=C2? (Charlie Mike)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Newly built Slingshot rudder =?ISO-8859-1?Q?question? |
I just acquired a newly built, never flown slingshot. The builder attached the
rudder hinge, using every other marked rivet point on the hinge. Im concerned
his short cut compromises the strength and design. Should I go back and drill
every every rivet hole and use all of them?
I think I know the answer..
--------
Kolb Slingshot 582, E gearbox.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=501964#501964
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | =?UTF-8?Q?Re=3a_Kolb-List=3a_Newly_built_Slingshot_rudder_question?= |
=?UTF-8?B?w6LigqzCpg==?
On 5/16/2021 12:15 PM, Charlie Mike wrote:
>
> I just acquired a newly built, never flown slingshot. The builder attached the
rudder hinge, using every other marked rivet point on the hinge. Im concerned
his short cut compromises the strength and design. Should I go back and drill
every every rivet hole and use all of them?
> I think I know the answer..
>
> --------
> Kolb Slingshot 582, E gearbox.
The question you *didn't* ask is, "Should I go back and check every
builder-installed joint in the a/c?"
I think you know the answer to that, too.
;-)
--
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: UTF-8?Q?Re:_Kolb-List:_Newly_built_?= =?UTF-8?Q?Slingshot_rudder_question=C3=A2=82=AC=C2? |
My old Original Firestar used all of the holes.
Bill Sullivan
On Sunday, May 16, 2021, 01:15:32 PM EDT, Charlie Mike <chuckmiranda8@
gmail.com> wrote:
I just acquired a newly built, never flown slingshot.=C2- The builder att
ached the rudder hinge, using every other marked rivet point on the hinge.
I=C3=A2=82=AC=84=A2m concerned his short cut compromises the strength
and design.=C2- Should I go back and drill every every rivet hole and us
e all of them?
I think I know the answer=C3=A2=82=AC=C2..
--------
Kolb Slingshot 582, E gearbox.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=501964#501964
S -
WIKI -
-
=C2- =C2- =C2- =C2- =C2- -Matt Dralle, List Admin.
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Newly built Slingshot rudder =?ISO-8859-1?Q?question=C3=A2=82=AC=C2? |
Yeah, thanks gents. Im gonna go back and do it right
--------
Kolb Slingshot 582, E gearbox.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=501977#501977
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Newly built Slingshot rudder =?ISO-8859-1?Q?question=C3=A2=82=AC=C2? |
Yeah, thanks gents. Im gonna go back and do it right
--------
Kolb Slingshot 582, E gearbox.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=501978#501978
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|