Lightning-List Digest Archive

Tue 06/05/07


Total Messages Posted: 5



Today's Message Index:
----------------------
 
     1. 04:42 AM - Re: N730AL Panel (Jim Langley)
     2. 03:44 PM - Cover It Up! (Pete)
     3. 04:12 PM - Re: Cover It Up! (IFLYSMODEL@AOL.COM)
     4. 06:20 PM - Lightning is coming! (Jim Langley)
     5. 07:43 PM - Re: Lightning is coming! (Colin J. Kennedy)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:42:14 AM PST US
    From: "Jim Langley" <pequeajim@gmail.com>
    Subject: N730AL Panel
    Thanks Mark. All good suggestions and I will take all of it in to consideration. All of this feedback will help me in my final decision. Jim! _____ From: owner-lightning-list-server@matronics.com [mailto:owner-lightning-list-server@matronics.com] On Behalf Of Mark Stauffer Sent: Monday, June 04, 2007 11:53 PM Subject: RE: Lightning-List: N730AL Panel Jim, A couple more points to ponder while in the design phase. The depth between the panel and the forward bulkhead is approximately 11.75=94 and can be bumped out to 12=94 if necessary. Any more than that and you start running into other issues. Also, the canopy tip up arms will come into play. With the GRT Sport EFIS systems we have about =BC=94 clearance between the arm and the back of the instrument case. You can move the arms slightly right or left but again only a little because it will cause other problems. Double check the dimensions of your particular EFIS unit to make sure the tip up arms won=92t be a factor. Also look at what type of connector you have and where it=92s located. Again with the GRT Sports we have to be careful where we place the unit in the panel because of the 25 pin D-sub connector that comes out of the back of the case. If we place the unit too far outboard then the connector interferes with the tip up arms. One last thing (for now at least!) to consider. Ask Ryan or Nick for the dimensions of the instrument panel bulkhead. While you are able to trim this bulkhead you should take it into consideration while designing your panel. As a general rule we do not place anything along the top inch or so of the panel. I=92d hate for you to invest a lot of money in a system that may or may not fit well. Hope this is helpful to you. Mark From: owner-lightning-list-server@matronics.com [mailto:owner-lightning-list-server@matronics.com] On Behalf Of Jim Langley Sent: Sunday, June 03, 2007 10:19 PM Subject: Lightning-List: N730AL Panel I=92m working on my panel concepts. Right now I have three different rough concepts and will probably change it around a dozen times before I settle for my final design. Thought I would send it out for some evaluation and comments. You can be brutal if you need to as I don=92 take things personal. Jim! <<...>>


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 03:44:22 PM PST US
    From: "Pete" <pete@flylightning.net>
    Subject: Cover It Up!
    Great covers now available. $350.00 with Lightning Logo. Silver Standard and in stock. Custom colors available special order. Made from Sunbrella with soft inside surface. Call Dana to order. Pete


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:12:51 PM PST US
    From: IFLYSMODEL@AOL.COM
    Subject: Re: Cover It Up!
    Hey Pete: Cover look good. I guess I have a problem with left and right? How did you make them both look the same? Lynn Nelsen ************************************** See what's free at http://www.aol.com.


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:20:57 PM PST US
    From: "Jim Langley" <pequeajim@gmail.com>
    Subject: Lightning is coming!
    I got the word today that my Lightning will arrive at Green Landings on the 18th. Looks like a looooong weekend coming up after it gets there! (calm down Jim.)


    Message 5


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 07:43:45 PM PST US
    From: "Colin J. Kennedy" <cjk129@cox.net>
    Subject: Lightning is coming!
    Great Jim! I'm looking forward to your web site. Colin K. OK -----Original Message----- From: owner-lightning-list-server@matronics.com [mailto:owner-lightning-list-server@matronics.com] On Behalf Of Jim Langley Sent: Tuesday, June 05, 2007 8:20 PM Subject: Lightning-List: Lightning is coming! I got the word today that my Lightning will arrive at Green Landings on the 18th. Looks like a looooong weekend coming up after it gets there! (calm down Jim.)




    Other Matronics Email List Services

  • Post A New Message
  •   lightning-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Lightning-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/lightning-list
  • Browse Lightning-List Digests
  •   http://www.matronics.com/digest/lightning-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --