----------------------------------------------------------
                           Lightning-List Digest Archive
                                      ---
                     Total Messages Posted Thu 01/03/13: 8
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 09:01 AM - Horizontal tail goes on 2013 exp demo  (Nick Otterback)
     2. 09:06 AM - Outboard horizontal tail finish MK2  (Nick Otterback)
     3. 09:08 AM - Horizotal tail leading edge inspection hole  (Nick Otterback)
     4. 09:11 AM - Alternative to molded in cabin NACA scoops  (Nick Otterback)
     5. 09:12 AM - Picture of Outside cabin NACA scoop  (Nick Otterback)
     6. 09:37 AM - New molded in elevator trim tab and inspection cover  (Nick Otterback)
     7. 09:39 AM - Close up trim tab cut out  (Nick Otterback)
     8. 09:44 AM - Elevator hinge shim  (Nick Otterback)
 
 
 
________________________________  Message 1  _____________________________________


Time: 09:01:50 AM PST US
Subject: Lightning-List: Horizontal tail goes on 2013 exp demo
From: Nick Otterback <vettin74@yahoo.com>


Mk2 tail install complete on 2013 exp demo.


Nick

Sent from my pocket 
<pre><b><font size=2 color="#000000" face="courier new,courier">


</b></font></pre></body></html>

________________________________  Message 2  _____________________________________


Time: 09:06:09 AM PST US
Subject: Lightning-List: Outboard horizontal tail finish MK2
From: Nick Otterback <vettin74@yahoo.com>


This is how the end of our tail looks. The cut back of course if for elevato
r down clearance. The new tail needs less elevator travel. Up travel is limi
ted to 15 degrees while down travel is between 12-15 degrees. All new kits s
hip with this tail.

Nick

Sent from my pocket 

<pre><b><font size=2 color="#000000" face="courier new,courier">


</b></font></pre></body></html>

________________________________  Message 3  _____________________________________


Time: 09:08:22 AM PST US
Subject: Lightning-List: Horizotal tail leading edge inspection hole
From: Nick Otterback <vettin74@yahoo.com>


If glassing the tail on, save some time and dont finish the inspection cover
. No nut plates or rivets, just glue it shut and glass over with the lower g
ap tape. 

Nick

Sent from my pocket 

<pre><b><font size=2 color="#000000" face="courier new,courier">


</b></font></pre></body></html>

________________________________  Message 4  _____________________________________


Time: 09:11:19 AM PST US
Subject: Lightning-List: Alternative to molded in cabin NACA scoops
From: Nick Otterback <vettin74@yahoo.com>


We have cut the molded in NACA scoops out of the fuselage and installed SV2 s
coops from VANs. Provides a nice finish on the outside.

Nick

Sent from my pocket 

<pre><b><font size=2 color="#000000" face="courier new,courier">


</b></font></pre></body></html>

________________________________  Message 5  _____________________________________


Time: 09:12:01 AM PST US
Subject: Lightning-List: Picture of Outside cabin NACA scoop
From: Nick Otterback <vettin74@yahoo.com>


Follow up picture to the cabin NACA vent.

Nick

Sent from my pocket 
<pre><b><font size=2 color="#000000" face="courier new,courier">


</b></font></pre></body></html>

________________________________  Message 6  _____________________________________


Time: 09:37:41 AM PST US
Subject: Lightning-List: New molded in elevator trim tab and inspection cover
From: Nick Otterback <vettin74@yahoo.com>


This elevator is new from custom fiberglass with premolded trim tab and cut o
ut. Also prefinished is the location of the trim motor inspection cover. Bui
lding is about the same. Look for updates to the manual once this one is com
plete.

Nick

Sent from my pocket 

<pre><b><font size=2 color="#000000" face="courier new,courier">


</b></font></pre></body></html>

________________________________  Message 7  _____________________________________


Time: 09:39:15 AM PST US
Subject: Lightning-List: Close up trim tab cut out
From: Nick Otterback <vettin74@yahoo.com>


Pre finish close outs. 

Nick

Sent from my pocket 
<pre><b><font size=2 color="#000000" face="courier new,courier">


</b></font></pre></body></html>

________________________________  Message 8  _____________________________________


Time: 09:44:29 AM PST US
Subject: Lightning-List: Elevator hinge shim
From: Nick Otterback <vettin74@yahoo.com>


To prevent paint from scuffing off the hinge during operation install a shim
. We built shims 0.010 in thickness to fit between the hinge and elevator. T
he movement is much smoother and the paint stays put.

Nick

Sent from my pocket 

<pre><b><font size=2 color="#000000" face="courier new,courier">


</b></font></pre></body></html>

 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               lightning-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Lightning-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/lightning-list
Browse Digests                   http://www.matronics.com/digest/lightning-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.